Hello, Reviving a bit of an old thread.
On Thu, Jul 15, 2021 at 11:50:22AM +0200, Maxime Ripard wrote: > On Tue, Jul 06, 2021 at 05:44:58PM +0100, Dave Stevenson wrote: > > On Tue, 6 Jul 2021 at 16:13, Maxime Ripard wrote: > > > > > > On a similar theme, some devices want the clock lane in HS mode > > > > > > early > > > > > > so they can use it in place of an external oscillator, but the data > > > > > > lanes still in LP-11. There appears to be no way for the > > > > > > display/bridge to signal this requirement or it be achieved. > > > > > > > > > > You're right. A loooong time ago, the omapdrm driver had an internal > > > > > infrastructure that didn't use drm_bridge or drm_panel and instead > > > > > required omapdrm-specific drivers for those components. It used to > > > > > model > > > > > the display pipeline in a different way than drm_bridge, with the sync > > > > > explicitly setting the source state. A DSI sink could thus control its > > > > > enable sequence, interleaving programming of the sink with control of > > > > > the source. > > > > > > > > > > Migrating omapdrm to the drm_bridge model took a really large effort, > > > > > which makes me believe that transitioning the whole subsystem to > > > > > sink-controlled sources would be close to impossible. We could add > > > > > DSI-specific operations, or add another enable bridge operation > > > > > (post_pre_enable ? :-D). Neither would scale, but it may be enough. > > > > > > > > I haven't thought it through for all generic cases, but I suspect it's > > > > more a pre_pre_enable that is needed to initialise the PHY etc, > > > > probably from source to sink. I believe it could be implemented as a pre-pre-enable indeed. It feels like a bit of a hack, as the next time we need more fine-grained control over the startup sequence, we'll have to add a pre-pre-pre-enable. Given that the startup sequence requirements come from the sink device, it would make sense to let it explicitly control the initialization, instead of driving it from the source. I don't think we'll be able to rework the bridge API in that direction though, so I'm fine with a hack. > > > > If the panel/bridge can set a flag that can be checked at this point > > > > for whether an early clock is required or not, I think that allows us > > > > to comply with the requirements for a large number of panels/bridges > > > > (LP-11 vs HS config for clock and or data lanes before pre_enable is > > > > called). > > > > > > > > pre_enable retains the current behaviour (initialise the chain from > > > > sink to source). > > > > enable then actually starts sending video and enabling outputs. > > > > > > Flags indeed seem like a more contained option. Another one could be to > > > have a mipi_dsi_host to (for example) power up the clock lane that would > > > be called by default before the bridge's enable, or at the downstream > > > bridge driver discretion before that. > > > > Which driver will that call? > > The parent DSI Host > > > An extreme example perhaps, but Toshiba make the TC358860 eDP to DSI > > bridge chip[1]. So the encoder will be eDP, but the DSI config needs > > to go to that bridge. Does that happen automatically within the > > framework? I guess so as the bridge will have called > > mipi_dsi_host_register for the DSI sink to attach to. > > In that case, whatever sink would be connected to the bridge would call > the bridge clock enable hook if it needs it in its pre_enable, or it > would be called automatically before enable if it doesn't > > Would that help? Sounds good to me, in theory at least (let's see what issues we'll run into in practice :-)). Has anyone given it a try, or is planning to ? > > Perhaps a new mipi_dsi_host function to configure the PHY is the > > easier solution. If it can allow the sink to request whatever > > combination of states from clock and data lanes that it fancies, then > > it can be as explicit as required for the initialisation sequence, and > > the host driver does its best to comply with the requests. > > I don't know, I'm not really fond in general of solutions that try to > cover any single case if we don't need it and / or have today an issue > with this. I'd rather have something that works for the particular > bridge we were discussing, see if it applies to other bridges and modify > it if it doesn't until it works for all our cases. Trying to reason in > all possible cases tend to lead to solutions that are difficult to > maintain and usually over-engineered. A DSI host clock enable operation or a DSI host PHY configuration operation both fit in the same place in the grand scheme of things, so I don't mind either. We should be able to easily move from a more specific operation to a more generic one if the need arises. > > I'd have a slight query over when and how the host would drop to ULPS > > or power off. It probably shouldn't be in post_disable as the sink > > hasn't had a chance to finalise everything in its post_disable. > > > > Perhaps pm_runtime with autosuspend is the right call there? > > pm_runtime semantics mean that once the device is suspended, its power > domains, regulators, clocks, etc. are all shut down, so it doesn't > really fit the low power state expected by DSI > > > [1] > > https://toshiba.semicon-storage.com/ap-en/semiconductor/product/interface-bridge-ics-for-mobile-peripheral-devices/display-interface-bridge-ics/detail.TC358860XBG.html > > > > > > When I discussed this briefly with Maxime there was a suggestion of > > > > using pm_runtime to be able to power up the pipeline as a whole. If > > > > the bridge driver can use pm_runtime to power up the PHY when > > > > required, then that may solve the issue, however I know too little of > > > > the details to say whether that is actually practical. > > > > > > I'm not sure it was about this topic in particular. If I remember well > > > our discussion, this was about the vc4 driver that tries to circumvent > > > the framework and call the pre_enable and enable hooks itself because it > > > wasn't properly powered before and thus any DCS-related call by the > > > downstream bridge or panel would end up creating a CPU stall. > > > > > > I suggested to use runtime_pm in the DCS related calls to make sure the > > > device is powered because there's no relation between the state of the > > > downstream bridge or panel and whether it can send DCS commands or not. > > > For all we know, it could do it at probe time. > > > > pm_runtime is all a bit of a magic black box to me. > > > > We had discussed shifting to using pm_runtime from DCS (and enable) > > calls to power up the PHY on demand, and that's what I implemented. > > However Laurent flagged up that using > > dsi->encoder->crtc->state->adjusted_mode to get the HS clock info > > required to send a HS DCS command from that call is deprecated, so how > > do we specify the clock rate to use at that point? > > I guess the most sensible would be to have a custom bridge state, and > add a pointer to the current bridge state in struct drm_bridge. Then, as > long as you have a bridge pointer you have a way to get the current > state associated to it, and since we already have atomic_duplicate_state > / atomic_destroy_state we can create our own structure around it storing > whatever we want. That's a good point. It would only be needed if we use runtime PM to work around the initialization sequence issue, not if we implement a DSI host clock enable/disable operation, right ? > > > > > > host_transfer calls can supposedly be made at any time, however > > > > > > unless > > > > > > MIPI_DSI_MSG_USE_LPM is set in the message then we're meant to send > > > > > > it > > > > > > in high speed mode. If this is before a mode has been set, what > > > > > > defines the link frequency parameters at this point? Adopting a > > > > > > random > > > > > > default sounds like a good way to get undefined behaviour. > > > > > > > > > > > > DSI burst mode needs to set the DSI link frequency independently of > > > > > > the display mode. How is that meant to be configured? I would have > > > > > > expected it to come from DT due to link frequency often being chosen > > > > > > based on EMC restrictions, but I don't see such a thing in any > > > > > > binding. > > > > > > > > > > Undefined too. DSI support was added to DRM without any design effort, > > > > > it's more a hack than a real solution. The issue with devices that can > > > > > be controlled over both DSI and I2C is completely unhandled. So far > > > > > nobody has really cared about implementing DSI right as far as I can > > > > > tell. > > > > > > > > :-( > > > > > > > > Thinking aloud, does having the option to set a burst link frequency > > > > from DT (or ACPI) have any issue for other platforms? > > > > Looking at the handling of MIPI_DSI_MODE_VIDEO_BURST in the various > > > > drivers, all except stm/dw_mipi_dsi-stm.c appear to take it as a "use > > > > all the defined timings, but drop to LP during blanking" option. The > > > > link frequency has therefore remained a property of the > > > > display/bridge. > > > > dw_mipi_dsi-stm.c cranks the PLL up by 20%, but I haven't followed > > > > through the full detail of the parameters it computes from there. > > > > > > I don't see anything wrong with using link-frequency from the DT to > > > setup the burst frequency. It's what v4l2 has been using for a while > > > without any known (to me) drawback, and we're using the same of-graph > > > bindings, so it shouldn't be too controversial there. How would that frequency we picked in practice ? Do panels typically support a range of HS frequencies for DCS HS transfers ? > > OK, that sounds like a vague plan. > > > > > > DSI and I2C controlled devices is yet another issue that I haven't > > > > even looked at. > > > > I think it's more that vc4 wants to ignore DSI should the DSI host > > > > node be enabled in DT, but there's no panel bound to it. One could say > > > > that is a DT error and tough luck, but from a user's perspective that > > > > is a bit harsh. > > > > > > I guess the larger "issue" is that the tree in the DT is done following > > > the "control" bus, and Linux likes to tie the life cycle of a given > > > device to its parent bus. Both these decisions make sense, but they > > > interact in a weird way in some occurrences (like this one, or Allwinner > > > has an Ethernet PHY controlled through MMIO which end up in the same > > > case). > > > > > > I wonder if using device links here could help though. > > > > I really don't know about that one. > > It's a piece of infrastructure that was created at first (I think?) to > model the power dependency between devices that don't have a parent / > child relationship. For example, if you use DMA, you probably want to > keep the IOMMU powered as long as you are, but it is in a completely > separate branch of the "device tree" (not one from the DTB, the one that > linux DM creates). > > It was later expanded to also cover probe order and make sure a supplier > would probe before its consumer, effectively making EPROBE_DEFER > obsolete. > > The second part is still fairly new, but I think we can solve this by > adding a device link between the DSI host and whatever is at the end of > the OF-Graph endpoint. > > > > > > > As a follow on, bridge devices can support burst mode (eg TI's > > > > > > SN65DSI83 that's just been merged), so it needs to know the desired > > > > > > panel timings for the output side of the bridge, but the DSI link > > > > > > timings to set up the bridge's PLL. What's the correct way for > > > > > > signalling that? drm_crtc_state->adjusted_mode vs > > > > > > drm_crtc_state->mode? Except mode is userspace's request, not what > > > > > > has > > > > > > been validated/updated by the panel/bridge. > > > > > > > > > > adjusted_mode is also a bit of a hack, it solves very specific issues, > > > > > and its design assumes a single encoder in the chain with no extra > > > > > bridges. We should instead add modes to the bridge state, and > > > > > negotiate > > > > > modes along the pipeline the same way we negotiate formats. > > > > > > > > So as I understand it we already have format negotiation between > > > > bridges via atomic_get_output_bus_fmts and atomic_get_input_bus_fmts, > > > > so is it possible to extend that to modes? > > > > Are you thinking bridge state that is owned by the framework, or by > > > > the individual bridge drivers? > > > > > > atomic_check is made for that. I guess we could improve its call > > > sequence to each time a mode is modified along the bridge list we > > > restart the sequence until all components agree (or reject it entirely > > > if they can't), but I don't really see why we would need yet another > > > hook. Isn't this what atomic_get_output_bus_fmts() and atomic_get_input_bus_fmts() implement ? > > Why do all nodes in the bridge list need to agree? Adjacent nodes need > > to agree, but they then also need to retain that agreed timing > > somewhere. > > We might have mutually exclusive requirements though? Let's use the > example of the VC4 HDMI driver that can't have odd horizontal timings, > and assume it's a constraint of our DSI driver instead. > > Then, we have a DSI->LVDS bridge, a LVDS->RGB bridge and a panel (which > is a bit ridiculous, but whatever). If the LVDS->RGB bridge can't have > even horizontal timings, then you just can't display it, even though > they are not adjacent (unless the bridge in the middle can modify the > timings between the input and output, but that's not always possible). > > Similarly, if for the RGB panel we need to increase a bit some timings > to accommodate for a larger pixel clock and end up above what the DSI > host can provide, we're also done. The hard part will be to figure out a good heuristics to perform the negotiation without going back and forth (at least not in a way that would require too many iterations, and certainly avoiding infinite loops). That will be an interesting problem to solve, but maybe we'll be lucky and a simple approach will work for the use cases we have to support today. > > Taking SN65DSI8[3|4|5] as an example, it supports burst mode, and the > > DSI frequency and timings are permitted to be different from that > > which it uses on the LVDS side. The LVDS panel and LVDS side of DSI83 > > need to agree over the format, and the DSI host and DSI side of DSI83 > > need to agree, but they may be two different timings. > > Register 0x0B (DSI_CLK_DIVIDER & REFCLK_MULTIPLIER) allows you to > > configure the LVDS rate compared to the DSI rate (the driver currently > > goes for 1:1), and registers 0x20 to 0x34 allow you to set the number > > of active pixel and blanking on the LVDS side (again currently just > > copied across). > > > > The way I'm seeing burst mode as having been interpreted at present is > > that it's largely just a flag to say "drop to LP mode between lines". > > The timing that needs to be passed to the crtc is therefore going to > > be based on the DSI link rate (converted to pixels) with increased > > blanking periods. > > > > I guess there are similarities with Media Controller and V4L2 here. A > > typical chain there could be: > > sensor -> scaler -> crop -> CSI-2 receiver. > > The format on each of those links may be different, but the chain as a > > whole needs to be valid. Media Controller largely relies on userspace > > to configure all links, but with a DRM chain that isn't really an > > option as it's expected that the display chain configures itself. > > Also, the userspace has no concept of media sub-devices in DRM, so it > just sets the mode on the whole DRM/KMS device, unlike what v4l2 does. > In v4l2, afaik, if you ended up with the above scenarios it would just > be rejected when you set the format on the link, letting the userspace > figure it out. We can't really do that here I wonder how long we'll be able to keep userspace out of the picture to configure the internals of the pipeline. I don't want to be the first person who will have a use case that requires this. -- Regards, Laurent Pinchart