Hello Krzysztof,
uto, 6. lip 2023. u 09:14 Krzysztof Kozlowski
<krzysztof.kozlow...@linaro.org> napisao je:
>
> On 05/06/2023 17:35, Paulo Pavacic wrote:
> > Fannal C3004 is a 480x800 display made by fannal that requires
> > DCS initialization sequences.
> >
> > Signed-off-by: Paulo Pavacic <pavaci...@gmail.com>
> > ---
>
> > v3 changelog:
> > - using generic mipi_dsi_dcs_write_seq
>
> This is marked as v2?
I have ruined numbering. At first this driver was named
panel-mipi-dsi-bringup and parts of it weren't handled under patchset.
>
> > - removed success prints
> > - removed some comments
> > - simplified code/removed support for different panels
> > - changed namespace from fann to fannal
> > v2 changelog:
> > - renamed from panel-mipi-dsi-bringup
> > - only one MAINTAINER e-mail
> > ---
> > MAINTAINERS
>
>
> > +static int fannal_panel_probe(struct mipi_dsi_device *dsi)
> > +{
> > + struct device *dev = &dsi->dev;
> > + struct fannal_panel_data *panel_data;
> > + int ret;
> > +
> > + panel_data = devm_kzalloc(&dsi->dev, sizeof(*panel_data), GFP_KERNEL);
> > +
> > + if (!panel_data)
> > + return -ENOMEM;
> > +
> > + panel_data->reset = devm_gpiod_get_optional(
> > + dev, "reset", GPIOD_OUT_LOW | GPIOD_FLAGS_BIT_NONEXCLUSIVE);
>
> dev should be in previous line
>
> Why this is nonexclusive? How many instances of same driver are
> expecting to get this on one system?
>
> > +
> > + if (IS_ERR(panel_data->reset)) {
> > + ret = PTR_ERR(panel_data->reset);
> > + dev_err(dev,
> > + "error: probe: get reset GPIO: (%d) Check the fdt\n",
> > + ret);
>
> return dev_err_probe
>
> > + return ret;
> > + }
> > +
> > + mipi_dsi_set_drvdata(dsi, panel_data);
> > +
> > + dsi->format = MIPI_DSI_FMT_RGB888;
> > + dsi->mode_flags = MIPI_DSI_CLOCK_NON_CONTINUOUS |
> > + MIPI_DSI_MODE_VSYNC_FLUSH | MIPI_DSI_MODE_VIDEO_HSE
> > |
> > + MIPI_DSI_MODE_NO_EOT_PACKET |
> > + MIPI_DSI_MODE_VIDEO_SYNC_PULSE |
> > MIPI_DSI_MODE_VIDEO;
> > + dsi->lanes = 2;
> > +
> > + gpiod_set_value_cansleep(panel_data->reset, 1);
>
> So you leave the panel in reset state?
yes
> > +
> > + drm_panel_init(&panel_data->panel, dev, &fannal_panel_funcs,
> > + DRM_MODE_CONNECTOR_DSI);
> > + dev_set_drvdata(dev, panel_data);
> > +
> > + drm_panel_add(&panel_data->panel);
> > +
> > + ret = mipi_dsi_attach(dsi);
> > + if (ret) {
> > + drm_panel_remove(&panel_data->panel);
> > + dev_err(dev, "error: probe fail: can't attach mipi_dsi!\n");
>
> No need to shout, skip exclamation mark.
>
>
> Best regards,
> Krzysztof
>
Thanks,
Paulo
