>> >> > DSI device lifetime has three different stages:
>> >> > 1. before the DSI link being powered up and clocking,
>> >> > 2. when the DSI link is in LP state (for the purpose of this question,
>> >> > this is the time between the DSI link being powered up and the video
>> >> > stream start)
>> >> > 3. when the DSI link is in HS state (while streaming the video).
>> >>
>> >> It's not clear to me what (2) is. What is the state of the clock and
>> >> data lanes?
>> >
>> > Clk an Data0 should be in the LP mode, ready for LP Data Transfer.
>>
>> Then this is somehow missing
>> https://docs.kernel.org/gpu/drm-kms-helpers.html#mipi-dsi-bridge-operation
>>
>>    A DSI host should keep the PHY powered down until the pre_enable
>> operation
>>    is called. All lanes are in an undefined idle state up to this point,
>> and
>>    it must not be assumed that it is LP-11. pre_enable should initialise
>> the
>>    PHY, set the data lanes to LP-11, and the clock lane to either LP-11
>> or HS
>>    depending on the mode_flag MIPI_DSI_CLOCK_NON_CONTINUOUS.
>>
>> So I don't think these three states are sufficient, see below, that
>> there
>> should be at least four.
>
>Which one is #4?

enabled clock lane (HS mode), data lanes in LP-11

-michael

>>
>> >
>> > I don't think we support ULPS currently.
>> >
>> >
>> >>
>> >> I'm facing similar issues with the tc358775 bridge. This bridge needs
>> >> to release its reset while both clock and data lanes are in LP-11
>> >> mode.
>> >> But then it needs to be configured (via I2C) while the clock lane is
>> >> in enabled (HS mode), but the data lanes are still in LP-11 mode.
>> >>
>> >> To me it looks like there is a fouth case then:
>> >> 1. unpowered
>> >> 2. DSI clock and data are in LP-11
>> >> 3. DSI clock is in HS and data are in LP-11
>> >> 4. DSI clock is in HS and data is in HS
>> >>
>> >> (And of course the bridge needs continuous clock mode).
>> >>
>> >> > Different DSI bridges have different requirements with respect to the
>> >> > code being executed at stages 1 and 2. For example several DSI-to-eDP
>> >> > bridges (ps8640, tc358767 require for the link to be quiet during
>> >> > reset time.
>> >> > The DSI-controlled bridges and DSI panels need to send some commands
>> >> > in stage 2, before starting up video
>> >> >
>> >> > In the DRM subsystem stage 3 naturally maps to the
>> >> > drm_bridge_funcs::enable, stage 1 also naturally maps to the
>> >> > drm_bridge_funcs::pre_enable. Stage 2 doesn't have its own place in
>> >> > the DRM call chain.
>> >> > Earlier we attempted to solve that using the pre_enable_prev_first,
>> >> > which remapped pre-enable callback execution order. However it has led
>> >> > us to the two issues. First, at the DSI host driver we do not know
>> >> > whether the panel / bridge were updated to use pre_enable_prev_first
>> >> > or not. Second, if the bridge has to perform steps during both stages
>> >> > 1 and 2, it can not do that.
>> >> >
>> >> > I'm trying to find a way to express the difference between stages 1
>> >> > and 2 in the generic code, so that we do not to worry about particular
>> >> > DSI host and DSI bridge / panel peculiarities when implementing the
>> >> > DSI host and/or DSI panel driver.
>> >>
>> >> For now, I have a rather hacky ".dsi_lp11_notify" callback in
>> >> drm_bridge_funcs which is supposed to be called by the DSI host while
>> >> the
>> >> clock and data lanes are in LP-11 mode. But that is rather an RFC and
>> >> me
>> >> needing something to get the driver for this bridge working. Because
>> >> it's
>> >> badly broken. FWIW, you can find my work-in-progress patches at
>> >> https://github.com/mwalle/linux/tree/feature-tc358775-fixes
>> >>
>> >> -michael
>> >>
>> >
>> >
>> > --
>> > With best wishes
>> > Dmitry
>
>
>

Reply via email to