On 2024/12/10 19:02, Dmitry Baryshkov wrote:
On Tue, Dec 10, 2024 at 02:54:00PM +0800, Fange Zhang wrote:
From: Li Liu <[email protected]>
Add display MDSS and DSI configuration for QCS615 RIDE board.
QCS615 has a DP port, and DP support will be added in a later patch.
Signed-off-by: Li Liu <[email protected]>
Signed-off-by: Fange Zhang <[email protected]>
---
arch/arm64/boot/dts/qcom/qcs615-ride.dts | 89 ++++++++++++++++++++++++++++++++
1 file changed, 89 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/qcs615-ride.dts
b/arch/arm64/boot/dts/qcom/qcs615-ride.dts
index
a25928933e2b66241258e418c6e5bc36c306101e..694719a09ac46bfa2fe34f1883c0970b9d0902be
100644
--- a/arch/arm64/boot/dts/qcom/qcs615-ride.dts
+++ b/arch/arm64/boot/dts/qcom/qcs615-ride.dts
@@ -32,6 +32,18 @@ xo_board_clk: xo-board-clk {
#clock-cells = <0>;
};
};
+
+ dp-connector {
+ compatible = "dp-connector";
+ label = "DP";
+ type = "mini";
+
+ port {
+ dp_connector_out: endpoint {
+ remote-endpoint = <&anx_7625_out>;
+ };
+ };
+ };
};
&apps_rsc {
@@ -202,6 +214,83 @@ &gcc {
<&sleep_clk>;
};
+&i2c2 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ ioexp: gpio@3e {
+ compatible = "semtech,sx1509q";
+ reg = <0x3e>;
+ interrupt-parent = <&tlmm>;
+ interrupts = <58 0>;
Use IRQ flags instead of just 0 (here and further on). Also it might be
better to use interrupts-extended instead.
Got it, will use interrupts-extended instead
- interrupt-parent = <&tlmm>;
- interrupts = <58 0>;
+ interrupts-extended = <&tlmm 58 IRQ_TYPE_NONE>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ semtech,probe-reset;
+ };
+
+ i2c-mux@77 {
+ compatible = "nxp,pca9542";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
Add empty line before device nodes (here and furher on).
Sorry, will add it in next patch.
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ anx7625@58 {
+ compatible = "analogix,anx7625";
+ reg = <0x58>;
+ interrupt-parent = <&ioexp>;
+ interrupts = <0 0>;
will change it to interrupts-extended in next patch
- interrupt-parent = <&ioexp>;
- interrupts = <0 0>;
+ interrupts-extended = <&ioexp 0 IRQ_TYPE_NONE>;
+ enable-gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
+ wakeup-source;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ anx_7625_in: endpoint {
+ remote-endpoint =
<&mdss_dsi0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ anx_7625_out: endpoint {
+ remote-endpoint =
<&dp_connector_out>;
+ };
+ };
+ };
+ };
+ };
+ };
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dsi0 {
+ vdda-supply = <&vreg_l11a>;
+ status = "okay";
+};
+
+&mdss_dsi0_out {
+ remote-endpoint = <&anx_7625_in>;
+ data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+ vdds-supply = <&vreg_l5a>;
+ status = "okay";
+};
+
&qupv3_id_0 {
status = "okay";
};
--
2.34.1
