Le 11/02/2025 à 12:44, AngeloGioacchino Del Regno a écrit :
Add a driver for the Himax HX8279-D MIPI-DSI DriverIC with support
for the Startek KX070FHFID078 7.0" 1200x1920 IPS panel, found on
various MediaTek Genio Evaluation Kit boards.
...
+ if (!hx->skip_goa_config) {
+ if ((desc->goa_stv_lead_time_ck > HX8279_P3_GOA_STV_LEAD) ||
+ (desc->goa_ckv_lead_time_ck > HX8279_P3_GOA_CKV_LEAD) ||
+ (desc->goa_ckv_dummy_vblank_num > HX8279_P3_GOA_CKV_DUMMY))
+ return dev_err_probe(dev, -EINVAL,
+ "Invalid lead timings in GOA
config\n");
+ /*
+ * Don't perform zero check for polarity and start position, as
+ * both pol=0 and start=0 are valid configuration values.
+ */
+ num_clr = 0;
+ for (i = 0; i < ARRAY_SIZE(desc->goa_clr_start_pos); i++) {
+ if (desc->goa_clr_start_pos[i] < 0)
+ continue;
+ else if (desc->goa_clr_start_pos[i] >
HX8279_P3_GOA_CLR_CFG_STARTPOS)
+ return dev_err_probe(dev, -EINVAL,
+ "Invalid start position for
CLR%d\n", i + 1);
+ else
+ num_clr++;
+ }
+ if (!num_clr)
+ return -EINVAL;
+
+ for (i = 0; i < ARRAY_SIZE(desc->goa_clr_polarity); i++) {
+ if (num_clr < 0)
+ return -EINVAL;
+
+ if (desc->goa_clr_polarity[i] < 0)
+ continue;
+ else if (desc->goa_clr_polarity[i] > 1)
+ return dev_err_probe(dev, -EINVAL,
+ "Invalid polarity for
CLR%d\n", i + 1);
+ else if (desc->goa_clr_polarity[i] >= 0)
The if () looks superfluous.
+ num_clr--;
+ }
+ }
+
+ /* MIPI Configuration validation */
+ if (!desc->bta_tlpx && !desc->lhs_settle_time_by_osc25 &&
+ !desc->ths_settle_time && !desc->timing_unk_b8 &&
+ !desc->timing_unk_bc && !desc->timing_unk_d6)
+ hx->skip_mipi_timing = true;
+
+ /* Gamma Configuration validation */
+ if (desc->gamma_ctl > (HX8279_P6_GAMMA_POCGM_CTL |
HX8279_P6_GAMMA_POGCMD_CTL))
+ return -EINVAL;
+
+ return 0;
+}
+
+static int hx8279_probe(struct mipi_dsi_device *dsi)
+{
...
+ /* If the panel is connected on two DSIs then DSI0 left, DSI1 right */
+ if (hx->desc->is_dual_dsi) {
+ const struct mipi_dsi_device_info *info = &hx->desc->dsi_info;
+ struct mipi_dsi_host *dsi_r_host;
+ struct device_node *dsi_r;
+
+ dsi_r = of_graph_get_remote_node(dsi->dev.of_node, 1, -1);
+ if (!dsi_r)
+ return dev_err_probe(dev, -ENODEV, "Cannot get secondary DSI
node.\n");
+
+ dsi_r_host = of_find_mipi_dsi_host_by_node(dsi_r);
+ of_node_put(dsi_r);
+ if (!dsi_r_host)
+ return dev_err_probe(dev, -EPROBE_DEFER,
+ "Cannot get secondary DSI host\n");
+
+ hx->dsi[1] = devm_mipi_dsi_device_register_full(dev,
dsi_r_host, info);
+ if (IS_ERR(hx->dsi[1]))
+ return dev_err_probe(dev, PTR_ERR(hx->dsi[1]),
+ "Cannot get secondary DSI node\n");
+ num_dsis++;
+ mipi_dsi_set_drvdata(hx->dsi[1], hx);
+ }
+
+ hx->dsi[0] = dsi;
+ mipi_dsi_set_drvdata(dsi, hx);
+
+ drm_panel_init(&hx->panel, dev, &hx8279_panel_funcs,
DRM_MODE_CONNECTOR_DSI);
+
+ ret = drm_panel_of_backlight(&hx->panel);
+ if (ret)
+ return dev_err_probe(dev, ret, "Failed to get backlight\n");
+
+ drm_panel_add(&hx->panel);
+
+ for (i = 0; i < num_dsis; i++) {
+ hx->dsi[i]->lanes = hx->desc->num_lanes;
+ hx->dsi[i]->format = MIPI_DSI_FMT_RGB888;
+
+ hx->dsi[i]->mode_flags = MIPI_DSI_CLOCK_NON_CONTINUOUS |
+ MIPI_DSI_MODE_LPM;
+
+ if (hx->desc->mode_data[0].is_video_mode)
+ hx->dsi[i]->mode_flags |= MIPI_DSI_MODE_VIDEO |
+
MIPI_DSI_MODE_VIDEO_SYNC_PULSE;
+
+ ret = devm_mipi_dsi_attach(dev, hx->dsi[i]);
+ if (ret < 0) {
+ /* If we fail to attach to either host, we're done */
+ if (num_dsis == 2)
+ mipi_dsi_device_unregister(hx->dsi[1]);
Is it needed?
(devm_mipi_dsi_device_register_full() was used)
+
+ return dev_err_probe(dev, ret,
+ "Cannot attach to DSI%d host.\n",
i);
+ }
+ }
+
+ /* Make sure we start in a known state: panel off */
+ gpiod_set_value_cansleep(hx->reset_gpio, 0);
+ gpiod_set_value_cansleep(hx->enable_gpio, 0);
+
+ return 0;
+}
...
CJ
