On Thu, Sep 25, 2025 at 11:06:01AM +0530, Ayushi Makhija wrote:
> Add device tree nodes for the DSI0 controller with their corresponding
> PHY found on Qualcomm QCS8300 SoC.
>
> Signed-off-by: Ayushi Makhija <[email protected]>
> ---
> arch/arm64/boot/dts/qcom/qcs8300.dtsi | 95 ++++++++++++++++++++++++++-
> 1 file changed, 94 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/qcs8300.dtsi
> b/arch/arm64/boot/dts/qcom/qcs8300.dtsi
> index e0e1f63fc45b..834ae0522f2f 100644
> --- a/arch/arm64/boot/dts/qcom/qcs8300.dtsi
> +++ b/arch/arm64/boot/dts/qcom/qcs8300.dtsi
> @@ -3,6 +3,7 @@
> * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
> */
>
> +#include <dt-bindings/clock/qcom,dsi-phy-28nm.h>
> #include <dt-bindings/clock/qcom,qcs8300-gcc.h>
> #include <dt-bindings/clock/qcom,rpmh.h>
> #include <dt-bindings/clock/qcom,sa8775p-camcc.h>
> @@ -4854,6 +4855,13 @@ dpu_intf0_out: endpoint {
> remote-endpoint =
> <&mdss_dp0_in>;
> };
> };
> +
> + port@1 {
> + reg = <1>;
> + dpu_intf1_out: endpoint {
> + remote-endpoint =
> <&mdss_dsi0_in>;
> + };
> + };
> };
>
> mdp_opp_table: opp-table {
> @@ -4881,6 +4889,89 @@ opp-650000000 {
> };
> };
>
> + mdss_dsi0: dsi@ae94000 {
> + compatible =
> "qcom,sa8775p-dsi-ctrl","qcom,mdss-dsi-ctrl";
qcom,qcs8300-dsi-ctrl. You might use three compatibles (qcs8300, sa8775p
and the generic one), but there should be qcs8300 one.
Also please add a whitespace after comma or (even better), keep one
compat per line (align on opening quote).
> + reg = <0x0 0x0ae94000 0x0 0x400>;
> + reg-names = "dsi_ctrl";
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <4>;
> +
> + clocks = <&dispcc MDSS_DISP_CC_MDSS_BYTE0_CLK>,
> + <&dispcc
> MDSS_DISP_CC_MDSS_BYTE0_INTF_CLK>,
> + <&dispcc MDSS_DISP_CC_MDSS_PCLK0_CLK>,
> + <&dispcc MDSS_DISP_CC_MDSS_ESC0_CLK>,
> + <&dispcc MDSS_DISP_CC_MDSS_AHB_CLK>,
> + <&gcc GCC_DISP_HF_AXI_CLK>;
> + clock-names = "byte",
> + "byte_intf",
> + "pixel",
> + "core",
> + "iface",
> + "bus";
> +
> + assigned-clocks = <&dispcc
> MDSS_DISP_CC_MDSS_BYTE0_CLK_SRC>,
> + <&dispcc
> MDSS_DISP_CC_MDSS_PCLK0_CLK_SRC>;
> + assigned-clock-parents = <&mdss_dsi0_phy
> DSI_BYTE_PLL_CLK>,
> + <&mdss_dsi0_phy
> DSI_PIXEL_PLL_CLK>;
> +
> + phys = <&mdss_dsi0_phy>;
> +
> + operating-points-v2 = <&mdss_dsi_opp_table>;
> + power-domains = <&rpmhpd RPMHPD_MMCX>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + mdss_dsi0_in: endpoint {
> + remote-endpoint =
> <&dpu_intf1_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + mdss_dsi0_out: endpoint {
> + };
> + };
> + };
> +
> + mdss_dsi_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-358000000 {
> + opp-hz = /bits/ 64 <358000000>;
> + required-opps =
> <&rpmhpd_opp_svs_l1>;
> + };
> + };
> + };
> +
> + mdss_dsi0_phy: phy@ae94400 {
> + compatible = "qcom,sa8775p-dsi-phy-5nm";
Add qcs8300-specific compatible and use sa8775p as a fallback
> + reg = <0x0 0x0ae94400 0x0 0x200>,
> + <0x0 0x0ae94600 0x0 0x280>,
> + <0x0 0x0ae94900 0x0 0x27c>;
> + reg-names = "dsi_phy",
> + "dsi_phy_lane",
> + "dsi_pll";
> +
> + #clock-cells = <1>;
> + #phy-cells = <0>;
> +
> + clocks = <&dispcc MDSS_DISP_CC_MDSS_AHB_CLK>,
> + <&rpmhcc RPMH_CXO_CLK>;
> + clock-names = "iface", "ref";
> +
> + status = "disabled";
> + };
> +
> mdss_dp0_phy: phy@aec2a00 {
> compatible = "qcom,qcs8300-edp-phy",
> "qcom,sa8775p-edp-phy";
>
> @@ -5008,7 +5099,9 @@ dispcc: clock-controller@af00000 {
> <&mdss_dp0_phy 0>,
> <&mdss_dp0_phy 1>,
> <0>, <0>,
> - <0>, <0>, <0>, <0>;
> + <&mdss_dsi0_phy DSI_BYTE_PLL_CLK>,
> + <&mdss_dsi0_phy DSI_PIXEL_PLL_CLK>,
> + <0>, <0>;
> power-domains = <&rpmhpd RPMHPD_MMCX>;
> #clock-cells = <1>;
> #reset-cells = <1>;
> --
> 2.34.1
>
--
With best wishes
Dmitry
