From: Gary Guo <[email protected]> This is now handled by the macro itself.
Signed-off-by: Gary Guo <[email protected]> --- drivers/gpu/nova-core/driver.rs | 2 +- drivers/gpu/nova-core/gpu.rs | 4 ++-- drivers/gpu/nova-core/gsp/boot.rs | 32 +++++++------------------------ 3 files changed, 10 insertions(+), 28 deletions(-) diff --git a/drivers/gpu/nova-core/driver.rs b/drivers/gpu/nova-core/driver.rs index 5a4cc047bcfc..e39885c0d5ca 100644 --- a/drivers/gpu/nova-core/driver.rs +++ b/drivers/gpu/nova-core/driver.rs @@ -70,7 +70,7 @@ impl pci::Driver for NovaCore { fn probe(pdev: &pci::Device<Core>, _info: &Self::IdInfo) -> impl PinInit<Self, Error> { pin_init::pin_init_scope(move || { - dev_dbg!(pdev.as_ref(), "Probe Nova Core GPU driver.\n"); + dev_dbg!(pdev, "Probe Nova Core GPU driver.\n"); pdev.enable_device_mem()?; pdev.set_master(); diff --git a/drivers/gpu/nova-core/gpu.rs b/drivers/gpu/nova-core/gpu.rs index 9b042ef1a308..60c85fffaeaf 100644 --- a/drivers/gpu/nova-core/gpu.rs +++ b/drivers/gpu/nova-core/gpu.rs @@ -262,13 +262,13 @@ pub(crate) fn new<'a>( ) -> impl PinInit<Self, Error> + 'a { try_pin_init!(Self { spec: Spec::new(pdev.as_ref(), bar).inspect(|spec| { - dev_info!(pdev.as_ref(),"NVIDIA ({})\n", spec); + dev_info!(pdev,"NVIDIA ({})\n", spec); })?, // We must wait for GFW_BOOT completion before doing any significant setup on the GPU. _: { gfw::wait_gfw_boot_completion(bar) - .inspect_err(|_| dev_err!(pdev.as_ref(), "GFW boot did not complete\n"))?; + .inspect_err(|_| dev_err!(pdev, "GFW boot did not complete\n"))?; }, sysmem_flush: SysmemFlush::register(pdev.as_ref(), bar, spec.chipset)?, diff --git a/drivers/gpu/nova-core/gsp/boot.rs b/drivers/gpu/nova-core/gsp/boot.rs index 581b412554dc..1582e1a65274 100644 --- a/drivers/gpu/nova-core/gsp/boot.rs +++ b/drivers/gpu/nova-core/gsp/boot.rs @@ -170,15 +170,10 @@ pub(crate) fn boot( Some(libos_handle as u32), Some((libos_handle >> 32) as u32), )?; - dev_dbg!( - pdev.as_ref(), - "GSP MBOX0: {:#x}, MBOX1: {:#x}\n", - mbox0, - mbox1 - ); + dev_dbg!(pdev, "GSP MBOX0: {:#x}, MBOX1: {:#x}\n", mbox0, mbox1); dev_dbg!( - pdev.as_ref(), + pdev, "Using SEC2 to load and run the booter_load firmware...\n" ); @@ -190,19 +185,10 @@ pub(crate) fn boot( Some(wpr_handle as u32), Some((wpr_handle >> 32) as u32), )?; - dev_dbg!( - pdev.as_ref(), - "SEC2 MBOX0: {:#x}, MBOX1{:#x}\n", - mbox0, - mbox1 - ); + dev_dbg!(pdev, "SEC2 MBOX0: {:#x}, MBOX1{:#x}\n", mbox0, mbox1); if mbox0 != 0 { - dev_err!( - pdev.as_ref(), - "Booter-load failed with error {:#x}\n", - mbox0 - ); + dev_err!(pdev, "Booter-load failed with error {:#x}\n", mbox0); return Err(ENODEV); } @@ -216,11 +202,7 @@ pub(crate) fn boot( Delta::from_secs(5), )?; - dev_dbg!( - pdev.as_ref(), - "RISC-V active? {}\n", - gsp_falcon.is_riscv_active(bar), - ); + dev_dbg!(pdev, "RISC-V active? {}\n", gsp_falcon.is_riscv_active(bar),); // Create and run the GSP sequencer. let seq_params = GspSequencerParams { @@ -239,8 +221,8 @@ pub(crate) fn boot( // Obtain and display basic GPU information. let info = commands::get_gsp_info(&mut self.cmdq, bar)?; match info.gpu_name() { - Ok(name) => dev_info!(pdev.as_ref(), "GPU name: {}\n", name), - Err(e) => dev_warn!(pdev.as_ref(), "GPU name unavailable: {:?}\n", e), + Ok(name) => dev_info!(pdev, "GPU name: {}\n", name), + Err(e) => dev_warn!(pdev, "GPU name unavailable: {:?}\n", e), } Ok(()) -- 2.51.2
