When an HDMI connector is forced enabled (e.g. via video=HDMI-A-1:e for laptop clamshell operation) and the external monitor enters DPMS standby, some monitors (such as the BenQ GW2790Q) power down their internal DDC/I2C controller, causing SCDC/EDID reads to fail with -ENXIO (-6).
Currently, intel_hdmi_detect() and intel_hdmi_force() unconditionally call intel_hdmi_unset_edid() before calling intel_hdmi_set_edid(). When drm_edid_read_ddc() returns NULL during monitor standby, the connector's cached detect_edid is wiped out and drm_helper_probe_single_connector_modes() falls back to the 1024x768 VESA no-EDID mode. When the monitor wakes back up, because the connector status remained forced to connector_status_connected, no hotplug state transition occurs and the display remains stuck at 1024x768 until a manual mode probe (such as toggling the laptop lid) is triggered. Fix this by moving intel_hdmi_unset_edid() into intel_hdmi_set_edid() after checking whether a forced connector already has a valid cached EDID (detect_edid and edid_blob_ptr) when DDC fails, and only clearing detect_edid on Gen11+ digital port disconnect when the connector is not forced. When the monitor is awake or a different monitor is plugged in, drm_edid_read_ddc() succeeds, resets the previous EDID and dp_dual_mode state via intel_hdmi_unset_edid(), and updates the connector with the new EDID. v2: - Move intel_hdmi_unset_edid() into intel_hdmi_set_edid() so hotplug detection via intel_hdmi_detect() also preserves the cached EDID on forced connectors and resets dp_dual_mode when updating EDID. - Clear detect_edid on Gen11+ disconnect when the connector is unforced, and verify edid_blob_ptr is non-NULL before retaining detect_edid. Signed-off-by: Aman Sharma <[email protected]> --- drivers/gpu/drm/i915/display/intel_hdmi.c | 25 +++++++++++++++++------ 1 file changed, 19 insertions(+), 6 deletions(-) diff --git a/drivers/gpu/drm/i915/display/intel_hdmi.c b/drivers/gpu/drm/i915/display/intel_hdmi.c index b6fa1a1558b8..89ab9a790a41 100644 --- a/drivers/gpu/drm/i915/display/intel_hdmi.c +++ b/drivers/gpu/drm/i915/display/intel_hdmi.c @@ -2570,6 +2570,19 @@ intel_hdmi_set_edid(struct drm_connector *_connector) intel_gmbus_force_bit(ddc, false); } + /* + * If the connector is forced on (e.g. video=HDMI-A-1:e) and the sink's + * DDC/I2C bus is powered down during DPMS standby, keep the previously + * cached EDID rather than wiping it and falling back to 1024x768. + */ + if (!drm_edid && connector->base.force && + connector->detect_edid && connector->base.edid_blob_ptr) { + intel_display_power_put(display, POWER_DOMAIN_GMBUS, wakeref); + return true; + } + + intel_hdmi_unset_edid(&connector->base); + /* Below we depend on display info having been updated */ drm_edid_connector_update(&connector->base, drm_edid); @@ -2611,10 +2624,11 @@ intel_hdmi_detect(struct drm_connector *_connector, bool force) wakeref = intel_display_power_get(display, POWER_DOMAIN_GMBUS); if (DISPLAY_VER(display) >= 11 && - !intel_digital_port_connected(encoder)) + !intel_digital_port_connected(encoder)) { + if (!connector->base.force) + intel_hdmi_unset_edid(&connector->base); goto out; - - intel_hdmi_unset_edid(&connector->base); + } if (intel_hdmi_set_edid(&connector->base)) status = connector_status_connected; @@ -2638,10 +2652,10 @@ intel_hdmi_force(struct drm_connector *_connector) if (!intel_display_driver_check_access(display)) return; - intel_hdmi_unset_edid(&connector->base); - - if (connector->base.status != connector_status_connected) + if (connector->base.status != connector_status_connected) { + intel_hdmi_unset_edid(&connector->base); return; + } intel_hdmi_set_edid(&connector->base); } -- 2.43.0
