hi, i successfully compiled and run the mach64 branch of dri. glxinfo shows me that its working and the gears also showed some improvement. still there are some warnings in the XFree86.0.log, which i think may cause me some troubles with one application i installed DRI for. as i dont know if it is my fault or part of the current developement i would like to ask the experts.
thx 4 help erich here is the log from the application which causes the troubles: when i open the renderwindow it gives the errors, when i close it it crashes the program. ------------------------------------------------ GEM: Mark Danks GEM: ver: 0.84-5 GEM: compiled: Oct 28 2001 error: GEM: Unable to create single buffer window error: GEM: Error creating const context error: GEM: A serious error occured creating const Context error: GEM: Do not continue! GEM: window created map GEM: Start rendering GEM: Stop rendering X Error of failed request: BadValue (integer parameter out of range for operation) Major opcode of failed request: 128 (XFree86-DRI) Minor opcode of failed request: 13 () Value in failed request: 0x2000004 Serial number of failed request: 36 Current serial number in output stream: 36 socket receive error: Connection reset by peer (104) ----------------------------------------------------------- here the part of the XFree86.0.log : ------------------------------------------ (II) ATI(0): VESA BIOS detected (II) ATI(0): VESA VBE Version 2.0 (II) ATI(0): VESA VBE Total Mem: 8128 kB (II) ATI(0): VESA VBE OEM: ATI MACH64 (II) ATI(0): VESA VBE OEM Software Rev: 1.0 (II) ATI(0): VESA VBE OEM Vendor: ATI Technologies Inc. (II) ATI(0): VESA VBE OEM Product: MACH64RM (II) ATI(0): VESA VBE OEM Product Rev: 01.00 (II) ATI(0): VESA VBE DDC supported (II) ATI(0): VESA VBE DDC Level none (II) ATI(0): VESA VBE DDC transfer in appr. 2 sec. (II) ATI(0): VESA VBE DDC read failed (--) ATI(0): ATI 3D Rage Mobility graphics controller detected. (--) ATI(0): Chip type 4C4D "LM", version 4, foundry TSMC, class 0, revision 0x01. (--) ATI(0): AGP bus interface detected; block I/O base is 0x2000. (--) ATI(0): ATI Mach64 adapter detected. (--) ATI(0): Internal RAMDAC (subtype 1) detected. (==) ATI(0): RGB weight 565 (==) ATI(0): Default visual is TrueColor (==) ATI(0): Using gamma correction (1.0, 1.0, 1.0) (II) ATI(0): Using Mach64 accelerator CRTC. (--) ATI(0): 1024x768 panel (ID 2) detected. (--) ATI(0): Panel model NEC NL10276BC28-11F. (--) ATI(0): Panel clock is 65.146 MHz. (II) ATI(0): Using digital flat panel interface. (II) ATI(0): Storing hardware cursor image at 0x407FFC00. (II) ATI(0): Using 8 MB linear aperture at 0x40000000. (!!) ATI(0): Virtual resolutions will be limited to 8191 kB due to linear aperture size and/or placement of hardware cursor image area. (II) ATI(0): Using Block 0 MMIO aperture at 0x41000400. (II) ATI(0): Using Block 1 MMIO aperture at 0x41000000. (WW) ATI(0): Failed to set up write-combining range (0x40000000,0x800000) (II) ATI(0): MMIO write caching enabled. (--) ATI(0): 8192 kB of SDRAM (1:1) detected (using 8191 kB). (WW) ATI(0): Cannot shadow an accelerated frame buffer. (--) ATI(0): Internal programmable clock generator detected. (--) ATI(0): Reference clock 29.500 MHz. (II) ATI(0): Maximum clock: 230.00 MHz ----------------------------------------------------------------- _______________________________________________ Dri-devel mailing list [EMAIL PROTECTED] https://lists.sourceforge.net/lists/listinfo/dri-devel
