Hello, Masa!
Thanks for your response and commands!
Well...the network card still does not work, I've extracted the logs,
which I copy here:
ifconfig -a: (no changes)
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu
8232 index 1
inet 127.0.0.1 netmask ff000000
atge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index
2
inet 10.100.100.2 netmask ffffff00 broadcast 10.100.100.255
ether 0:1f:c6:8:f5:7f
lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu
8252 index 1
inet6 ::1/128
dmesg | grep atge: (here comes the first change)
Jul 7 20:00:14 osol01 atge: [ID 130221 kern.info] atge0: Attansic L2
(vid: 0x1969, did: 0x2048, revid: 0xa0)
Jul 7 20:00:14 osol01 atge: [ID 451511 kern.info] atge0: MII PHY
(0x004dd022) found at 0
Jul 7 20:00:14 osol01 atge: [ID 679413 kern.info] atge0: PHY
control:1000<ANE>,
status:7849<100_BASEX_FD,100_BASEX,10_BASE_FD,10_BASE,MFPRMBLSUPR,CANAUTONEG,EXTENDED>,
advert:de1<ASM_DIR,PAUSE,100BASE_TX_FD,100BASE_TX,10BASE_T_FD,10BASE_T>,
lpar:0, exp:0
Jul 7 20:00:14 osol01 gld: [ID 944156 kern.info] atge0: atheros L1 nic
driver v2.6.4: type "ether" mac address 00:1f:c6:08:f5:7f
Jul 7 20:00:14 osol01 pcie_pci: [ID 586369 kern.info] PCIE-device:
pci1043,8...@0, atge0
Jul 7 20:00:14 osol01 genunix: [ID 936769 kern.info] atge0
is /p...@0,0/pci8086,2...@1c,1/pci1043,8...@0
Jul 7 20:00:14 osol01 atge: [ID 188825 kern.info] atge0: gem_add_intrs:
supported intr_types:3
Jul 7 20:00:14 osol01 pcplusmp: [ID 805372 kern.info] pcplusmp:
pci1969,2048 (atge) instance 0 irq 0x19 vector 0x60 ioapic 0xff intin
0xff is bound to cpu 0
Jul 7 20:00:14 osol01 atge: [ID 716252 kern.info] atge0: resetting PHY
(there is no negotiation here)
grep atge /var/adm/messages:
Jul 7 20:00:14 osol01 atge: [ID 130221 kern.info] atge0: Attansic L2
(vid: 0x1969, did: 0x2048, revid: 0xa0)
Jul 7 20:00:14 osol01 atge: [ID 451511 kern.info] atge0: MII PHY
(0x004dd022) found at 0
Jul 7 20:00:14 osol01 atge: [ID 679413 kern.info] atge0: PHY
control:1000<ANE>,
status:7849<100_BASEX_FD,100_BASEX,10_BASE_FD,10_BASE,MFPRMBLSUPR,CANAUTONEG,EXTENDED>,
advert:de1<ASM_DIR,PAUSE,100BASE_TX_FD,100BASE_TX,10BASE_T_FD,10BASE_T>,
lpar:0, exp:0
Jul 7 20:00:14 osol01 gld: [ID 944156 kern.info] atge0: atheros L1 nic
driver v2.6.4: type "ether" mac address 00:1f:c6:08:f5:7f
Jul 7 20:00:14 osol01 pcie_pci: [ID 586369 kern.info] PCIE-device:
pci1043,8...@0, atge0
Jul 7 20:00:14 osol01 genunix: [ID 936769 kern.info] atge0
is /p...@0,0/pci8086,2...@1c,1/pci1043,8...@0
Jul 7 20:00:14 osol01 atge: [ID 188825 kern.info] atge0: gem_add_intrs:
supported intr_types:3
Jul 7 20:00:14 osol01 pcplusmp: [ID 805372 kern.info] pcplusmp:
pci1969,2048 (atge) instance 0 irq 0x19 vector 0x60 ioapic 0xff intin
0xff is bound to cpu 0
Jul 7 20:00:14 osol01 atge: [ID 716252 kern.info] atge0: resetting PHY
(same as before, no negotiation)
I understand that my router supports 10 mbps, it's a Linksys WRT54G. I
confirmed this with the manual, it has four 10/100 RJ45 switched ports.
Thanks again, Masa!
Best regards,
HeCSa.
_______________________________________________
driver-discuss mailing list
[email protected]
http://mail.opensolaris.org/mailman/listinfo/driver-discuss
