pt., 12 paź 2018 o 03:41 Wu, Hao A <hao.a...@intel.com> napisał(a): > > > -----Original Message----- > > From: Marcin Wojtas [mailto:m...@semihalf.com] > > Sent: Thursday, October 11, 2018 11:43 PM > > To: Wu, Hao A > > Cc: Ni, Ruiyu; Ard Biesheuvel; Tian, Feng; Tomasz Michalec; Dong, Eric; > > edk2- > > devel-01; Gao, Liming; nad...@marvell.com; Kinney, Michael D; Zeng, Star > > Subject: Re: [edk2] [PATCH v2 2/4] MdeModulePkg/SdMmcPciHcDxe: Add > > UhsSignaling to SdMmcOverride protocol > > > > wt., 9 paź 2018 o 13:51 Marcin Wojtas <m...@semihalf.com> napisał(a): > > > > > > wt., 9 paź 2018 o 13:45 Ard Biesheuvel <ard.biesheu...@linaro.org> > > napisał(a): > > > > > > > > On 9 October 2018 at 13:32, Marcin Wojtas <m...@semihalf.com> wrote: > > > > > wt., 9 paź 2018 o 13:28 Wu, Hao A <hao.a...@intel.com> napisał(a): > > > > >> > > > > >> > -----Original Message----- > > > > >> > From: edk2-devel [mailto:edk2-devel-boun...@lists.01.org] On > > Behalf Of Ard > > > > >> > Biesheuvel > > > > >> > Sent: Monday, October 08, 2018 11:10 PM > > > > >> > To: Marcin Wojtas; Ni, Ruiyu; Wu, Hao A > > > > >> > Cc: Tian, Feng; Tomasz Michalec; Dong, Eric; edk2-devel-01; Gao, > > Liming; > > > > >> > Nadav Haklai; Kinney, Michael D; Zeng, Star > > > > >> > Subject: Re: [edk2] [PATCH v2 2/4] MdeModulePkg/SdMmcPciHcDxe: > > Add > > > > >> > UhsSignaling to SdMmcOverride protocol > > > > >> > > > > > ... > > > > >> > > > > > >> > I suppose this is defined by the eMMC spec. > > > > >> > > > > > >> > Ruiyu, Hao, could you clarify? Are the host control 2 register > > > > >> > values > > > > >> > for HS200/HS400 defined by the eMMC spec? > > > > >> > > > > >> Hi Ard and Marcin, > > > > >> > > > > >> As far as I know, the EMMC Electrical Standard Spec 5.1 (latest) does > > not > > > > >> mention on how to set the "UHS Mode Select" field of the Host > > Control 2 > > > > >> Register when switching to HS200/HS400. (Actually, the EMMC spec > > does not > > > > >> mention Host Control 2 Register at all) > > > > >> > > > > >> When it comes to setting the bus mode for EMMC devices, the current > > > > >> implementation of the SdMmcPciHcDxe driver does a mapping when > > setting the > > > > >> Host Control 2 Register: > > > > >> > > > > >> EMMC High Speed SDR - Freq: 0-52 MHz, Data Rate: Single > > > > >> matches > > > > >> SD SDR25 - Freq: 0-50 MHz, Data Rate: Single > > > > >> > > > > >> EMMC High Speed DDR - Freq: 0-52 MHz, Data Rate: Dual > > > > >> matches > > > > >> SD DDR50 - Freq: 0-50 MHz, Data Rate: Dual > > > > >> > > > > >> EMMC HS200 - Freq: 0-200 MHz, Data Rate: Single > > > > >> matches > > > > >> SD SDR104 - Freq: 0-208 MHz, Data Rate: Single > > > > >> > > > > >> EMMC HS400 - Freq: 0-200 MHz, Data Rate: Dual > > > > >> matches > > > > >> SD None > > > > >> > > > > >> And there is no obvious counterpart for the EMMC HS400 mode in the > > SD > > > > >> spec. The driver currently sets the "UHS Mode Select" field to a > > reserved > > > > >> value 0x5. > > > > >> > > > > > > > > > > Thank you Hao, above is on par with what the default UhsSignaling > > > > > routine does in this patch. IMO especially in case the EMMC standard > > > > > is not unequivocal regarding UHS_MODE_SEL, I'd encourage to accept > > > > > some way of updating HostControl2 register, depending on the > > > > > implementation. What is your opinion Ard? > > > > > > > > > > > > > I would like to know where the current values in SdMmcPciHcDxe come > > > > from if they are not defined in any spec. > > > > > > > > How do we know which ones are the correct ones? > > > > > > Hao, can you justify used values? > > > > > > > Hi Hao, > > > > Can you please take a look at the UHS_MODE_SEL values source for eMMC? > > Hi Marcin, > > Sorry for the delayed response. > > For the current implementation of the SdMmcPciHcDxe driver, the selecting > of "UHS Mode Select" field value of the Host Control 2 Register is based > on a Max Clock Frequency & Data Rate (Single or Dual) matching > relationship between the: > > A. Table 3-6 of the SD Specifications Part 1 Physical Layer Simplified > Specification Version 4.10 > > and > > B. Table 4 of the EMMC Electrical Standard Spec 5.1 > > The matching details was included in my previous reply. The only missing > part is there seems no matching for the EMMC HS400 mode in the SD > specifications. For this case, we are currently using the same approach > with the Linux implementation, that is to set the "UHS Mode Select" to a > value of 0x5 (not standard). >
Hao, Thanks a lot for the clarification. Ard, Knowing the numbers details, what is your view of the UhsSignaling handling? Best regards, Marcin _______________________________________________ edk2-devel mailing list edk2-devel@lists.01.org https://lists.01.org/mailman/listinfo/edk2-devel
