Jim: My trusty 10 year old Yamaha YST-M101 powered speakers on my computer (purchased at Fry's in Sunnyvale!) have never received any RFI at up to 600w pep here at my station. Maybe it's the (guffaw!) "Active Servo Technology" in them that does it, eh? :)
For non powered speakers, I have an ancient pair of JBL Control 1's that sound very nice with the K3 in AFX mode, but I think I'm going to retire them as they take up way too much room and are the epitome of overkill for Ham Radio (Hey! They were on hand! I had to use them SOMEWHERE!). I have pretty decent grounding, however, and employ ferrites on all cables going in and out of the speakers and on the wall wart. I will probably move the Yamahas to the K3 when I get rid of the Control 1's. I guess I'm lucky! :) -lu-w4lt- K3 # 3192 Message: 10 Date: Tue, 05 Oct 2010 10:32:48 -0700 From: Jim Brown <j...@audiosystemsgroup.com> Subject: Re: [Elecraft] Use of external speakers/amp To: elecraft@mailman.qth.net Message-ID: <4cab6140.4010...@audiosystemsgroup.com> Content-Type: text/plain; charset=ISO-8859-1; format=flowed On 10/4/2010 6:40 AM, Rick Staley wrote: > In connection with the second topic, I wonder what other K3 owners > might have done. > Have you gained any improvement by using external speakers, PC-type > speakers with audio > amps built in, or even something like a stereo amp with hi fi speakers? The K3 is a very compact rig, which requires that the loudspeaker also be compact. That limits its performance, both in terms of output LEVEL and frequency response. The most important characteristic of a loudspeaker is the SMOOTHNESS of its frequency response. The LIMITS (how low, how high) don't matter nearly as much. One of the major differences between a good speaker and a poor one is that smoothness. Bumps in the frequency response add both amplitude and phase distortion, which makes speech much harder to understand. One of the few shortcomings of the K2 on SSB is that the narrow RX filter settings use the multi-stage CW filters, re-tuned to stagger their response, and the total response is VERY bumpy. The K2 sounds great when the TX filter is used for RX (the full width setting), but sounds just awful when those narrower settings are used. Another important characteristic of a loudspeaker is its VOLTAGE SENSITIVITY. That is, how much voltage does it take to achieve a certain loudness. Most hi-fi loudspeakers have pretty LOW sensitivity -- they are designed to be driven by 50-200W power amps. The K3 has a 1-2W power amp, so it needs a speaker with fairly high sensitivity (unless you also add an outboard power amp). And yes, as others have noted, amplified loudspeakers are notorious for having bad RFI problems. When I attend audio trade shows, I wander the exhibit floor with a Kenwood TH-F6A (2M/220/440 talkie) and use it as a signal injection probe to test for RFI. So far, I've found only two amplified loudspeakers that didn't have RFI problems. Both cost more than $3K. Bottom line -- if you're going to add an external speaker to any ham rig, choose one with very smooth (flat) response in the speech range (400 - 4,000 Hz), and with reasonably high sensitivity. 73, Jim Brown K9YC No virus found in this outgoing message Checked by PC Tools AntiVirus (6.1.0.25 - 6.14880). http://www.pctools.com/free-antivirus/ ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
