Erik,
I cannot confirm or deny, but the 2 sets of ATU.DATA should be "N/A" or
"--" when the KXPA100 is enabled.
Think about it a bit - the 2 data sets only pertain to the internal ATU
in the KX2/KX3. When the KXPA100 is enabled, that internal tuner is
bypassed because any ATU must be on the output of the KXPA100.
The 2 sets of ATU.DATA is for field and home operation of the base
KX2/KX3, not for the KXAT100.
73,
Don W3FPR
On 7/6/2017 9:23 AM, Erik Tkal wrote:
Any confirmation on this issue?
Thanks and 73,
Erik Tkal - W1QED
On Jun 18, 2017, at 13:00, E T <etks...@gmail.com> wrote:
BTW, the KX2 with 2.77 behaves exactly the same way when scrolling past the N/A
with the KXPA100 enabled.
Thanks and 73,
Erik Tkal - W1QED
On Jun 18, 2017, at 10:34 AM, E T <etks...@gmail.com
<mailto:etks...@gmail.com>> wrote:
Hi Wayne,
There is one major quirk with the new ATU.DATA menu item on the KX3. When using the KXPA100 the menu item shows up
with the label N/A and value "--". And then when you scroll up or down to the next menu item it takes up to
a second to show the correct label. Even when you are scrolling fast through the items and go past that one the N/A
appears and persists as you scroll. All the other transitions are immediate except this one. Shouldn't the label
still show as ATU.DATA and have the value show "--" or "N/A"? E.g. like 2M/4M shows as "not
inSt".
I'm going to update my KX2 to the beta that also has this and see if it also
shows the same quirk.
Thanks and 73,
Erik Tkal - W1QED
On Apr 27, 2017, at 11:38 PM, Wayne Burdick <n...@elecraft.com
<mailto:n...@elecraft.com>> wrote:
Hi all,
Rev. 2.70 KX3 firmware unintentionally reduced the max AF gain setting for both
speaker and headphones. (We improved the granularity of the AF GAIN control at
the low end but didn’t get around to scaling the high end back up to the
original level.)
If you were affected by this and would like to try the field test release (rev.
2.76), please email me directly.
This rev also includes the new “ATU DATA” menu entry, which gives you two full
sets of per-band ATU data for use when running the KX3 “barefoot” (without the
KXPA100/KXAT100). Typically one set would be used at home, the other in the
field. If you do a lot of outings, this can save you the trouble of re-matching
all of your antennas when you get home. Another use for this is with two
different antennas for a given band.
73,
Wayne
N6KR
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
<http://mailman.qth.net/mailman/listinfo/elecraft>
Help: http://mailman.qth.net/mmfaq.htm <http://mailman.qth.net/mmfaq.htm>
Post: mailto:Elecraft@mailman.qth.net <mailto:Elecraft@mailman.qth.net>
This list hosted by: http://www.qsl.net <http://www.qsl.net/>
Please help support this email list: http://www.qsl.net/donate.html
<http://www.qsl.net/donate.html>
Message delivered to etks...@gmail.com <mailto:etks...@gmail.com>
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to donw...@embarqmail.com
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com