Mine moves in .10 increments, but it seems to like the numbers
that end in 5. e.g. .350. I wouldn't worry too much about it.
set the low end to .3 or to .4, depending on conditions and the
voice you're listening to and call it good. The whole purpose of
the knobs is to let you adjust the bandwidth to match conditions.
73 Bill AE6JV
On 6/30/18 at 8:44 PM, elecraft@mailman.qth.net (Michael Gillen
via Elecraft) wrote:
Hmmm when I try that I get Shif=.05 however and when I turn
VFO-A it says N/A and it still moves in .10 increments?
On Jun 30, 2018, at 7:55 PM, Jack Brindle <jackbrin...@me.com> wrote:
PB CTRL should do what you want. See page 62 of the K3S manual.
Jack, W6FB
On Jun 30, 2018, at 7:31 PM, Michael Gillen via Elecraft
<elecraft@mailman.qth.net> wrote:
Good info on the filters I had never tried the LO/HI CUT
and I like it. One question: On my K3S I
cannot set the LO CUT to .35KHz it only steps in .10 increments
not 0.05 increments is there some CONFIG item I need to change?
I looked through the CONFIG menus and Fred Cady’s book
however I did not see anything about setting that step.
73,
Michael
KK6RWK
On Jun 30, 2018, at 5:37 PM, Bill Frantz <fra...@pwpconsult.com> wrote:
Congratulations. The K3 is a really nice radio with
extraordinary factory support.
For SSB, I set low cut to .35 KHz and adjust the upper
cut between 1.9 KHz and 2.8 KHz, depending
on conditions. Higher makes for easier copy, but lower will
eliminate more noise, and help with nearby stations. Remember,
the crystal filters are to protect the AtoD converter in the
receiver. The DSP has many useful settings between those of the
installed filters.
73 Bill AE6JV
On 6/30/18 at 5:07 PM, 1lasports...@cox.net (Bill) wrote:
I recently purchased a K3 and trying to set up for SSB.I do not do code.
Is there any recommended settings for the shift lo cut and width?
It has the KFL3A-400 and the KFL3A-12.8 8 pole filters installed
I have read the manual and it does not really help me.
Thanks
Bill
W3WGG
---------------------------------------------------------------------------
Bill Frantz | Re: Computer reliability, performance, and security:
408-356-8506 | The guy who *is* wearing a parachute is *not* the
www.pwpconsult.com | first to reach the ground. - Terence Kelly
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to mjgil...@yahoo.com
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to jackbrin...@me.com
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to fra...@pwpconsult.com
-----------------------------------------------------------------------
Bill Frantz | I don't have high-speed | Periwinkle
(408)356-8506 | internet. I have DSL. | 16345
Englewood Ave
www.pwpconsult.com | | Los Gatos,
CA 95032
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com