Scott,
Those 4 "ARMS" of the MMIC are the leads. Do NOT break the body of the
MMIC, you will destroy it.
Find the one lead that is cut at an angle (that is the input) and orient
it toward the center of the board. If you cannot see the angled end, it
is the lead closest to the dot on the body. If there is a hole in the
board, the body of the MMIC goes into that hole.
If there is no hole, orient the MMIC so the angled lead (or dot) is
toward the center of the board.
Solder those "ARMS" to the 4 solder pads below. If there is no hole for
the body you have to press the leads down with a screwdriver to make
contact with the solder pads, then do it.
No wires are necessary - just fill the holes on the solder pads with
solder and solder the leads flat onto the board.
73,
Don W3FPR
On 7/28/2018 8:26 PM, Scott wrote:
Arrgh. Where to begin. All was going well until "installing" U1 MAR-1
MMIC.
Initial inventory of said kit was missing U1 MAR-1 MMIC. FWIW, there
are no part numbers and no pictures in the pdf manual. So I emailed
parts@elecraft and they sent me E600080 MAR-1 MMIC in a plastic bag.
Upon inspection of this part during the build 2 weeks later it did not
look like a solderable part, there were no leads for the thru holes. It
appeared to be just plastic with a raised "+" on one side and two holes
on one end. So I emailed parts@elecraft and said there has to be a
mistake/problem and could they please check again and send the correct
part that was solderable. I received the second E600080 MAR-1 MMIC.
Meet the new boss same as the old boss... the parts were identical. Upon
closer inspection under magnification there is a "part" located inside
the "+". So cut it out and it is a very small black cylinder with 4
"arms" 90deg apart. If this is the correct part then I'll send back the
first one they sent me.
But here is the problem. The Ngen PCB Rev B (which is the PCB that I
have) has 4 "thru holes" for installing U1 MAR1 MMIC and there are no
leads from E600080 to solder it to the PCB. There are 4 "arms" but it
is unclear to me how these "arms" are to be soldered to the board.
Unless I solder wires in the 4 thru holes in the PCB and thence to the
"arms" of E600080 I have no idea how to solder this part to the PCB. The
pdf manual does not say anything about soldering wires into the thru
holes and thence to the "arms".
http://www.elecraft.com/manual/E740057_N-Gen_Manual_Rev_D.pdf
I'm hoping someone else has built this module kit lately and figured it
out or Elecraft is going to have to give me some guidance on how to
solder this part to the board because it sure is not obvious to me.
Scott
AD5HS
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to donw...@embarqmail.com
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com