Hello Bernie
I have a KPA500 and run it on solar power with a 120 volt AC inverter.
I have never seen the issues that you are recounting. The first thing to
do is check the voltage going in to the KPA500 with a good voltmeter.
The next thing is something in the KPA500 ac input circuit that might be
mis behaving. Put an AC voltmeter on the transformer primary and monitor
that. Those points should be pretty stiff. Bad circuit breakers could
be a problem. You might also have a bad circuit connection in an AC box
or even an outlet. I had such a situation and it caused poor regulation
and a slight terrible smell as the plastic was baking.
I ran my KPA500 only on 28 and 50 MHz, but had no problem getting gobs
of output on each band. VSWR was under 1.5:1. As I recaqll drive was
19-20 watts and output would easily hit 500 or even more with the 117
vac input. My inverter is a sine wave type by Xantrex, fed with a 500 AH
AGM battery. Lately I got a smaller 150AH lithium battery and the amp
still works just fine with 117 volts.
Dave K1WHS
On 3/7/2022 1:54 AM, Bernie and Cheryl wrote:
Dear Folks:
I have been using my KPA-500 (driven by the K3s and transmitting
through the KAT-500) for about five years now. I have long noticed
that, when first using it, or if it has sat idling for a while, the
amp's supply voltage will be low on transmit and won't go higher until
the amp has been used for a couple of minutes. This becomes critical
in some instances since, particularly on 20 meters, the supply voltage
will be below 60 volts on transmit for a while and won't increase
unless I reduce the drive power by a few watts. I do always reduce
the drive power to make sure the supply voltage stays at 60 or above
(I have been told that this keeps the amp operating within normal
limits and the math indicates that this will make sure the current
doesn't get too high). Once I've been transmitting for a minute or
two (I almost always use CW), the amp appears to warm up and I can
bump up the drive power a few watts for higher power output and still
keep the supply voltage at 60 or above.
For the record, the amp is plugged into a normal wall outlet supplying
117VAC (or whatever the house is supplying at that moment), though it
is not using any of the same outlets that the rest of the shack uses.
I realize it is highly likely that all the outlets in the shack are on
the same breaker, but my prior tube-type amp used to dim the lights a
bit when I keyed it and had it plugged into the same outlets as the
rest of the shack. That stopped happening once I switched the outlet
for the tube amp and now I'm using that same outlet solely for the
KPA-500.
My first question is whether any of you with a KPA-500 experience the
same thing, i.e., supply voltage is a little low at the beginning and
increases as the amp warms up?
My second question concerns the fact that, even with the amp warmed
up, I can seldom (if ever) hit 500 watts out on 20 meters, though I
can do it easily on all the other bands (I recognize that this is
likely caused by my antenna's characteristics on that band, though SWR
doesn't exceed 1.7 at any frequency that I use, even without the
tuner). I simply can't get the drive up high enough to get there,
without the supply voltage dipping below 60. Usually, I can get
between 350 to 425 watts out. Do you think this would be different if
I had a 220 volt outlet installed in the shack? For the record, I
recognize that the 100 watt or so decrease in power out doesn't make
that much difference. I am asking because I wonder if it would be
easier on the amp to run it off of a 220 volt outlet.
As always, thanks for any help and advice.
73 de Bernie, KF0QS
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to k1...@metrocast.net
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com
