David:
At 14:42 12/13/2007, David Wilburn wrote:
When doing this, are you still able to have paddles connected to the K3
to send corrections and unexpected information by hand?
YES>.. the K3 has a PADDLE input jack SEPARATE from the KEY (which would
come from the external keying device).
Tom N0SS
-
David Wilburn
[EMAIL PROTECTED]
K4DGW
K2 S/N 5982
On Thu, 2007-12-13 at 14:03 -0500, Van W1WCG wrote:
> Paul,
>
> The settings you give are identical to what I'm using, however you didn't
> mention setting the K3 CONFIG parameter PTT--KEY to OFF - dtr.
> This will match the settings you have in N1MM logger.
>
> 73, Van W1WCG
> K3 #42
>
> ----- Original Message -----
> From: "Paul" <[EMAIL PROTECTED]>
> To: <Elecraft@mailman.qth.net>
> Sent: Thursday, December 13, 2007 1:38 PM
> Subject: [Elecraft] K3 and N1MM Logger
>
>
> >I can get N1MM to see the K3. I am switching logging software, for the
> > K2 I used WriteLog. The frequency and mode show in the title bar for
> > N1MM. However, I can NOT get N1MM to send CW. to the K3. I see the
> > software thinking it is sending the CW (the stop light gets bright and
> > then dims).
> >
> > I am using a serial cable connected to the only serial port on the
> > computer running Windows XP. This same cable and port were able to load
> > the firmware. For the N1MM configuration I have set Com1 to Elecraft K3,
> > and the CW/Other box is checked. In the parameters for this port, I have
> > DTR set to CW and RTS set to Always on. I have tried other combinations
> > for the DTR and RTS settings and none seem to work. The CW/PTT port
> > address is 3F8.
> >
> > I appreciate guidance from those who have made this work.
> >
> > 73,
> >
> > :) PK (Paul - K3MZ K2 #3135 K3 #84)
> > _______________________________________________
> > Elecraft mailing list
> > Post to: Elecraft@mailman.qth.net
> > You must be a subscriber to post to the list.
> > Subscriber Info (Addr. Change, sub, unsub etc.):
> > http://mailman.qth.net/mailman/listinfo/elecraft
> >
> > Help: http://mailman.qth.net/subscribers.htm
> > Elecraft web page: http://www.elecraft.com
> _______________________________________________
> Elecraft mailing list
> Post to: Elecraft@mailman.qth.net
> You must be a subscriber to post to the list.
> Subscriber Info (Addr. Change, sub, unsub etc.):
> http://mailman.qth.net/mailman/listinfo/elecraft
>
> Help: http://mailman.qth.net/subscribers.htm
> Elecraft web page: http://www.elecraft.com
_______________________________________________
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
_______________________________________________
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
