Hi Stewart- Like you, I had a problem with my K3 going dead. Unlike you, I bought a factory-built unit. I did that because I wanted to know it was working properly from the start. That turned out to be one of those things that sounds like a good idea but doesn't withstand close scrutiny.
What I saw initially was an occasional error message (ERR PL1) when switching to another band, then the audio would decay to nothing over a 2 second period. Sometimes I could get it to recover by chnaging bands, sometimes not. Since it was factory built, they had me return my K3. They found the TCXO3-1 oscillator was grounding occasionally. The oscillator would continue to operate, but grounding it (the case? some component? dunno) caused the frequency to be pulled about 20 KHz and the receiver would die. They replaced the oscillator (probably unnecessary), added an insulator and re-ran VCO calibration. It's been rock-solid ever since. Bruce, NM5B Santa Fe, NM ----- Original Message ----- From: "Stewart Baker" <[EMAIL PROTECTED]> To: "AB7R" <[EMAIL PROTECTED]>; "Elecraft Reflector" <elecraft@mailman.qth.net> Sent: Monday, March 10, 2008 5:33 AM Subject: RE: [Elecraft] K3 - RX Problem after latest firmware update Greg, Have re-installed V1.75 & V1.57 again, no change. Here is a sequence which you might like to try:- POWER 80m LSB 3780 NORM LO CUT=0.15 SAV ALT1 NORM TX ON/OFF ALT1 TX ON/OFF Receive may be dead at this point If not continue with Select USB ALT1 TX ON/OFF Receive dead Switching bands, modes or NORM always restores receiver. I do (from my point of view) hope that I am not the only one with this funny.. 73 Stewart G3RXQ On Sun, 9 Mar 2008 12:30:15 -0700, AB7R wrote: > Stewart, > > Try installing the new firmware again. I just tried to recreate your report > and the radio performs as expected...no problem with RX after a transmit > with ALT1 set to 0.15 on the LO side. > > 73 > Greg > AB7R > > > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] Behalf Of Stewart Baker > Sent: Sunday, March 09, 2008 11:32 AM > To: Elecraft Reflector > Subject: [Elecraft] K3 - RX Problem after latest firmware update > > > I am not sure if there is an obscure problem after the latest MCU > and DSP update. Maybe others could check and see if it happens to > them ? > > Any band on SSB if I have the DSP set to ALT1 with the Low Cut set > at 0.15 Hz , then after going onto transmit the receiver appears > to be dead. If I set the DSP to NORM by pressing the knob the > receiver suddenly bursts into life... > This happens whether there is any transmit audio or RF out. > > 73 > Stewart G3RXQ > _______________________________________________ > Elecraft mailing list > Post to: Elecraft@mailman.qth.net > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com > No virus found in this incoming message. > Checked by AVG. > Version: 7.5.518 / Virus Database: 269.21.7/1322 - Release Date: 3/9/2008 > 12:17 PM > > No virus found in this outgoing message. > Checked by AVG. > Version: 7.5.518 / Virus Database: 269.21.7/1322 - Release Date: 3/9/2008 > 12:17 PM _______________________________________________ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com _______________________________________________ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com