I use a Power Gate PGS40 with a GSM battery backup, same as UPS but cheaper in terms of how long one can stay on the air, so the issues of what happens when one loses power, here are none existant. I experience quite frequent blips so power backup is important.
73, Bill K9YEQ K2 #35; KX1 #35; K3 #1744; mini mods ATS-3B -----Original Message----- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Phil LaMarche Sent: Sunday, June 07, 2009 1:58 PM To: 'wayne burdick'; 'Geoffrey Mackenzie-Kennedy' Cc: 'Elecraft Discussion List' Subject: Re: [Elecraft] K3 power sequencing With the lightening in Florida, I have a very large UPS on all my equipment and computers. Phil Philip LaMarche LaMarche Enterprises, Inc. www.instantgourmetspices.com www.w9dvm.com 800-395-7795 pin 02 727-944-3226 FAX 727-937-8834 NASFT 30210 K3 #1605 CCA 98 00827 W9DVM -----Original Message----- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of wayne burdick Sent: Sunday, June 07, 2009 2:23 PM To: Geoffrey Mackenzie-Kennedy Cc: Elecraft Discussion List Subject: [Elecraft] K3 power sequencing The preferred way to turn off the K3 is via the POWER switch. Or, from a computer, by sending a "PS0" command, then waiting at least half a second later dropping the /POWER_ON line. You can turn the rig off at the power supply if that is unavoidable. Just as with a "brownout," when the firmware senses a supply voltage dip to 9.5 V or lower, it shuts down everything as cleanly as possible. But it may not have time to update all changed parameters in EEPROM (current VFO frequencies, etc.). Thus when you turn power back on, you might find the VFO in the last location you were at when you switched to the current band. I once tried turning my K3 off with at power supply several dozen times to see if I could make anything bad happen. Nothing did. That said, do use the preferred method if you can. 73, Wayne N6KR On Jun 7, 2009, at 11:03 AM, Geoffrey Mackenzie-Kennedy wrote: > Joe, > > Many thanks for your help. > > I had been toying with the idea of buying a K3 for use at another QTH, > but there the mains supply is not 100% reliable. If bad things can > happen if the 13.8V supply shuts down as the result of a mains outage, > that is serious. > > 73, > Geoff > GM4ESD > > > Joe Planisky wrote on Sunday, June 07, 2009 5:45 PM > >> From the owners manual (page 44 in rev D2): >> >> "Remote Power On/Off >> >> A remote-control system can pull the POWER ON line to ground (ACC >> connector, pg. 18) to turn the K3 ON. To turn it OFF, the controller >> must send the K3 a "PS0;" remote-control command via the RS232 >> interface, then deactivate the POWER ON signal. This sequence >> ensures that nonvolatile memory is updated correctly before >> shut-down." >> >> Note that it doesn't say how long it takes to update the NVRAM after >> the above process is completed. In other words, how soon after >> deactivating the POWER ON signal can I shut down the 13.8V supply? >> >> 73 >> -- >> Joe KB8AP >> >> >> On Jun 7, 2009, at 9:10 AM, Geoffrey Mackenzie-Kennedy wrote: >> >>> >>> Is there any interface available on the K3 which would allow an >>> external automatic protective shutdown system to meet this >>> requirement, rather than having to press the POWER button by hand? > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net Please help support this email > list: http://www.qsl.net/donate.html > > --- http://www.elecraft.com ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html