EBo, Sure thing. Totally understandable, I've been all over the place too.
Thank you, -Tom On Dec 30, 2015 6:04 PM, "EBo" <[email protected]> wrote: > I am probably going to need a couple of weeks before I get back to the > DC area and have access to all my stuff. Can we postpone ramping up the > Gentoo thread until then? If you want to start before hand I do have a > Gentoo laptop with me, but I have other obligations for the holidays > that will keep me from doing to many extracurricular activities... > > EBo -- > > On Dec 30 2015 2:12 PM, Thomas Gambone II wrote: > > Thank you for the offer to support, EBo! > > > > With gentoo, I've gotten into it on the Odroid C1, though not too > > successfully. > > Can't figure out some quirkiness with slow booting that happens. > > > > May be worth staring another thread to discuss. > > > > Will revisit my unfinished attempt and loop back. > > > > Thank you, > > -Tom > > > > On Wed, Dec 30, 2015 at 3:23 PM, EBo <[email protected]> wrote: > > > >> If you end up working/developing on Gentoo, I will make time to lend > >> a > >> hand on that (or as much time as I can). > >> > >> EBo -- > >> > >> On Dec 30 2015 11:56 AM, Thomas Gambone II wrote: > >> > Neil, > >> > > >> > Are you using an off the shelf A20 board, or did you spin your > >> own? > >> > > >> > As for your distro, what was your approach? > >> > > >> > Did you start from scratch / Linux From Source approach, > >> > ending up with your development copy being nearly identical to the > >> > production copy? > >> > > >> > OR > >> > > >> > Did you start with a light / customizable distro like gentoo, > >> which > >> > has > >> > package management maintained on the dev side. > >> > Then you copy a subset of the system to create your production > >> > distro? > >> > > >> > Continuing Jepler's work with the Odroid boards or similar to make > >> a > >> > robust > >> > embedded controller appliance with LinuxCNC would be excellent to > >> > learn. > >> > > >> > Thank you, > >> > -Tom > >> > > >> > > >> > On Tue, Dec 29, 2015 at 3:27 PM, Rick Lair <[email protected]> > >> > wrote: > >> > > >> >> I will have to look further into this, but Fagor Automation, of > >> >> which we > >> >> have two controls in our shop, is based off of a Linux software, > >> and > >> >> these are "Embedded", straight to the control, no desktop-ish > >> look > >> >> and > >> >> feel. > >> >> > >> >> When you power the control on, it says "DECOMPRESSING LINUX", > >> >> > >> >> > >> >> -- > >> >> > >> >> Thanks > >> >> > >> >> > >> >> Rick Lair > >> >> Superior Roll & Turning LLC > >> >> 399 East Center Street > >> >> Petersburg MI, 49270 > >> >> PH: 734-279-1831 > >> >> FAX: 734-279-1166 > >> >> www.superiorroll.com > >> >> > >> >> > >> >> > >> >> > >> >> > >> > >> > ------------------------------------------------------------------------------ > >> >> _______________________________________________ > >> >> Emc-developers mailing list > >> >> [email protected] > >> >> https://lists.sourceforge.net/lists/listinfo/emc-developers > >> >> > >> > > >> > > >> > >> > ------------------------------------------------------------------------------ > >> > _______________________________________________ > >> > Emc-developers mailing list > >> > [email protected] > >> > https://lists.sourceforge.net/lists/listinfo/emc-developers > >> > >> > >> > >> > >> > ------------------------------------------------------------------------------ > >> _______________________________________________ > >> Emc-developers mailing list > >> [email protected] > >> https://lists.sourceforge.net/lists/listinfo/emc-developers > >> > > > > > ------------------------------------------------------------------------------ > > _______________________________________________ > > Emc-developers mailing list > > [email protected] > > https://lists.sourceforge.net/lists/listinfo/emc-developers > > > > ------------------------------------------------------------------------------ > _______________________________________________ > Emc-developers mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-developers > ------------------------------------------------------------------------------ _______________________________________________ Emc-developers mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-developers
