You can pick up a "not feeling well" or dead - older VCR in thrift shops or garage sales for 2-5 dollars. Most all of them had "packaged" modulators inside. A check of the modulator by connection to a TV and checking for sync is advisable. Remember to measure the voltage prior to ripping it out of the unit or proceed with caution as some of them I have encountered use odd voltages (3.8 to 11 volts). Good hunting //M. Taylor - (Dodging fires in Colorado)
-----Original Message----- From: Ralph Cameron [mailto:ral...@igs.net] Sent: Monday, July 24, 2000 9:16 PM To: Scott Lacey; Jim Bacher Cc: emc-p...@ieee.org Subject: Re: 8591EM monitor output Jeff: Radio Shack sells an RF modulator that will do the job. If you feed it to a VCR you can also record the results as well as view it on a TV set. As mentioned, it produces NTSC compatible video on CH3 or 4. Price should be around $25. U.S. Ralph Cameron EMC Consulting and Suppression of Consumer Electronics (after sale). ----- Original Message ----- From: "Scott Lacey" <sco...@world.std.com> To: "Jim Bacher" <jim_bac...@mail.monarch.com> Cc: <emc-p...@ieee.org> Sent: Monday, July 24, 2000 6:29 PM Subject: RE: 8591EM monitor output > > Jeff, > I think the piece of hardware you need is an RF Modulator. These output your > video on Channel 3 (sometimes switchable to channel 4). Should be available > for $25-$50 dollars. Try MCM Electronics (800 543-4330)if you can't find one > locally. The one I have is their P/N 33-1480 Audio/Video Modulator. It is > about 3" x 5" x 1", with an attached (120V) line cord, and a switch to > select CH3/CH4. > > Scott Lacey > > -----Original Message----- > From: owner-emc-p...@ieee.org [mailto:owner-emc-p...@ieee.org]On Behalf > Of Jim Bacher > Sent: Monday, July 24, 2000 3:42 PM > To: Bailey; Jeff; 'emc-pstc' > Subject: Fwd:8591EM monitor output > > > > forwarding for Jeff. > > ____________________Reply Separator____________________ > Subject: 8591EM monitor output > Author: "Bailey; Jeff" <jbai...@mysst.com> > Date: 7/24/00 12:06 PM > > Hello all, > > Have any of you successfully hooked up a television to an HP8590 series EMC > analyzer? The monitor output does provide NTSC format, I am now assuming > that I need to provide a carrier for the monitor output to ride on in order > for the TV to see the NTSC signal and know what to do with it. Is there an > easier way to do this than to build my own modulator? > > Thanks, > > Jeff Bailey > Compliance Engineering > SST - A Division of Woodhead Canada > Phone: (519) 725 5136 ext. 363 > Fax: (519) 725 1515 > Email: jbai...@sstech.on.ca > Web: www.sstech.on.ca > > ------------------------------------------- > This message is from the IEEE EMC Society Product Safety > Technical Committee emc-pstc discussion list. > > To cancel your subscription, send mail to: > majord...@ieee.org > with the single line: > unsubscribe emc-pstc > > For help, send mail to the list administrators: > Jim Bacher: jim_bac...@mail.monarch.com > Michael Garretson: pstc_ad...@garretson.org > > For policy questions, send mail to: > Richard Nute: ri...@ieee.org > > > > ------------------------------------------- > This message is from the IEEE EMC Society Product Safety > Technical Committee emc-pstc discussion list. > > To cancel your subscription, send mail to: > majord...@ieee.org > with the single line: > unsubscribe emc-pstc > > For help, send mail to the list administrators: > Jim Bacher: jim_bac...@mail.monarch.com > Michael Garretson: pstc_ad...@garretson.org > > For policy questions, send mail to: > Richard Nute: ri...@ieee.org > > > ------------------------------------------- This message is from the IEEE EMC Society Product Safety Technical Committee emc-pstc discussion list. To cancel your subscription, send mail to: majord...@ieee.org with the single line: unsubscribe emc-pstc For help, send mail to the list administrators: Jim Bacher: jim_bac...@mail.monarch.com Michael Garretson: pstc_ad...@garretson.org For policy questions, send mail to: Richard Nute: ri...@ieee.org ------------------------------------------- This message is from the IEEE EMC Society Product Safety Technical Committee emc-pstc discussion list. To cancel your subscription, send mail to: majord...@ieee.org with the single line: unsubscribe emc-pstc For help, send mail to the list administrators: Jim Bacher: jim_bac...@mail.monarch.com Michael Garretson: pstc_ad...@garretson.org For policy questions, send mail to: Richard Nute: ri...@ieee.org