top" style="font: inherit;">The cable gets tested with whatever is on the cable. The EUT then is to meet the standard. And if you also bundle the PoE supply with your EUT (not likely but possible) then the AC mains to that device would also suffer the same test. And when you include Safety considerations it gets more complicated.
And given the you have video and digital and your company, vicon-security, the EUT may not actually be ITE, but would instead need to meet EN 50130-4 Bill --- On Wed, 10/27/10, Reginald Henry <[email protected]> wrote: From: Reginald Henry <[email protected]> Subject: iec 61000 4-4 EFT Immunity Test ON POE IP CABLE To: [email protected] Date: Wednesday, October 27, 2010, 11:13 AM Hello all, I have an EUT that has the following data inputs 1) Video Data Coax Cables (BNC) INPUT 2) IP CABLE INPUT THAT COULD CONTAIN BOTH DIGITAL DATA AND POE OR SIMPLY DIGITAL DATA 3) 24vac INPUT I can config the EUT TO accept one of two (2) setup options A) 24vac with separate IP Cable CONTAINING DATA ONLY 2) POE (no 24vac connected) via the IP Cable that is also carrying digital . My setup is using an EFT Tester that goes out to a Capacitive Clamp TO COUPLE THE SPIKES ONTO THE DATA LINES Setup A is not the problem, it is a simple conventional setup where the data IP cable alone is receiving the 2kv spikes @ 5KHz rep rate alone. Once that test is completed the power supply will then receive 2kv spikes @ 5KHz rep rate spikes on the Line, Neutral,Gnd (with various combinations.) ************************************************************************ ******************************* Setup B is my conundrum, if I am using ONLY POE as my supply to the EUT the data line is (as you know) bundled into the IP Cable along with the POE. If I use the POE along there are spikes going straight into the input of the supply of the EUT . The question is given the standard .. is this a valid configuration to test the EUT ? (BTW the EUT is classified as ITE ) Thanking you in advance for your input, Best Regards, Reg Henry Reginald Henry Electrical Engineer Vicon Industries, Inc. Tel: (631) 952-2288 Ext: 310 Tel: (800) 645-9116 Ext: 310 Web: <http://www.vicon-cctv.com/> CONFIDENTIALITY NOTICE: This transmission may contain information that is privileged, confidential and/or exempt from disclosure under applicable law. If you are not the intended recipient, you are hereby notified that any disclosure, copying, distribution, or use of the information contained herein (including any reliance thereof)is strictly prohibited. If you receive this transmission in error, please immediately contact the sender and destroy the material in it's entirety,whether in electronic or hard copy format. The views expressed in this communication may not necessarily be the views held by the company. Thank you. - ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. To post a message to the list, send your e-mail to <[email protected]> All emc-pstc postings are archived and searchable on the web at: http://www.ieeecommunities.org/emc-pstc Graphics (in well-used formats), large files, etc. can be posted to that URL. Website: http://www.ieee-pses.org/ Instructions: http://listserv.ieee.org/request/user-guide.html List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas <[email protected]> Mike Cantwell <[email protected]> For policy questions, send mail to: Jim Bacher: <[email protected]> David Heald: <[email protected]> - ---------------------------------------------------------------- This message is from the IEEE Product Safety Engineering Society emc-pstc discussion list. To post a message to the list, send your e-mail to <[email protected]> All emc-pstc postings are archived and searchable on the web at http://www.ieeecommunities.org/emc-pstc Graphics (in well-used formats), large files, etc. can be posted to that URL. Website: http://www.ieee-pses.org/ Instructions: http://listserv.ieee.org/request/user-guide.html List rules: http://www.ieee-pses.org/listrules.html For help, send mail to the list administrators: Scott Douglas <[email protected]> Mike Cantwell <[email protected]> For policy questions, send mail to: Jim Bacher <[email protected]> David Heald <[email protected]>
