ip link resulted in this, greenmill@greenmill:~$ ip link 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN mode DEFAULT link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT qlen 1000 link/ether 54:27:1e:61:b9:6f brd ff:ff:ff:ff:ff:ff greenmill@greenmill:~$
On 4/8/2015 11:29 AM, sam sokolik wrote: > The directions are assuming you are connecting to eth1 - Are you? Do a > > ip link > > and see what physical connnections you have.. > > sam > > On 4/8/2015 10:17 AM, Rick Lair wrote: >> I just did all of this, rebooted, and I still have nothing regarding a >> eth1 connection in the /sbin/config -a output. >> >> I am running he latest version of master on my machine. >> >> Rick >> >> On 4/8/2015 11:01 AM, sam sokolik wrote: >>> THis has some really good info on setting up the nic.. Don't use the >>> manager gui. >>> >>> http://linuxcnc.org/docs/2.7/html/man/man9/hm2_eth.9.html >>> >>> Also - you need to be using 2.7+ of linuxcnc for Ethernet support. >>> >>> sam >>> >>> On 4/8/2015 9:56 AM, Rick Lair wrote: >>>> A few questions, on setting up a network connection and static IP >>>> >>>> 1. Should I use the Network Manager GUI, or should I modify the the >>>> /etc/network/interface file thru the terminal? >>>> >>>> 2. I have tried both of the above, and cannot get anything to come up >>>> under eth0 on the printout of /sbin/config -a. I looked at my test >>>> machine in my office, and that printout shows the eth0. Should I delete >>>> the Network manager utility, I see issues where one interferes with the >>>> other? >>>> >>>> 3. If I plug a network cable into the Ethernet port on the MB, shouldn't >>>> it recognize it's connected, and start working on its own? >>>> I pulled the board out, went in the office, threw together >>>> a PS, and peripherals, and it will not do anything network wise when >>>> plugging it into our network. >>>> >>>> >>>> Here I go again, climbing another almost vertical learning curve. >>>> >>>> Rick >>>> >>>> >>>> >>>> On 4/7/2015 2:36 PM, Peter C. Wallace wrote: >>>>> On Tue, 7 Apr 2015, Rick Lair wrote: >>>>> >>>>>> Date: Tue, 07 Apr 2015 14:14:58 -0400 >>>>>> From: Rick Lair <r...@superiorroll.com> >>>>>> To: Peter Wallace <p...@mesanet.com> >>>>>> Subject: Re: [Emc-users] 7i80 Setup ( Was PNCConf setup) >>>>>> >>>>>> I don't know if the SF server crashed or what, but here is the >>>>>> printout you asked about. >>>>>> >>>>>> Here is my printout, >>>>>> >>>>>> greenmill@greenmill:~$ /sbin/ifconfig -a >>>>>> lo Link encap:Local Loopback >>>>>> inet addr:127.0.0.1 Mask:255.0.0.0 >>>>>> inet6 addr: ::1/128 Scope:Host >>>>>> UP LOOPBACK RUNNING MTU:16436 Metric:1 >>>>>> RX packets:1894 errors:0 dropped:0 overruns:0 frame:0 >>>>>> TX packets:1894 errors:0 dropped:0 overruns:0 carrier:0 >>>>>> collisions:0 txqueuelen:0 >>>>>> RX bytes:113732 (111.0 KiB) TX bytes:113732 (111.0 KiB) >>>>>> >>>>>> wlan1 Link encap:Ethernet HWaddr 54:27:1e:61:b9:6f >>>>>> inet addr:192.168.1.142 Bcast:192.168.1.255 >>>>>> Mask:255.255.255.0 >>>>>> inet6 addr: fe80::5627:1eff:fe61:b96f/64 Scope:Link >>>>>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >>>>>> RX packets:34073 errors:0 dropped:0 overruns:0 frame:0 >>>>>> TX packets:11010 errors:0 dropped:0 overruns:0 carrier:0 >>>>>> collisions:0 txqueuelen:1000 >>>>>> RX bytes:6970707 (6.6 MiB) TX bytes:1200489 (1.1 MiB) >>>>>> >>>>>> greenmill@greenmill:~$ >>>>> OK so its not terribly suprising that you cant communicate with the >>>>> 7I80 since you have no active Ethernet interface, only active >>>>> interfaces are your WIFI and the loopback interface. >>>>> >>>>> I would launch the network manager, select wired and then add a >>>>> configuration for a static IP address on the available Ethernet NIC >>>>> >>>>> >>>>> Note that for initial communication (until you setup the 7I80's EEPROM >>>>> address to 10.10.10.10 and move W2 to select the new address) you will >>>>> have to disable your wireless since its IP address range overlaps the >>>>> 7I80s default IP address >>>>> >>>>> >>>>> >>>>> >>>>>> And the W1 and W2 jumpers haven't been touched, they are in the >>>>>> bottom position. >>>>>> >>>>>> Rick >>>>>> >>>>>> >>>>> Peter Wallace >>>>> Mesa Electronics >>>>> >>>>> (\__/) >>>>> (='.'=) This is Bunny. Copy and paste bunny into your >>>>> (")_(") signature to help him gain world domination. >>>>> >>> ------------------------------------------------------------------------------ >>> BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT >>> Develop your own process in accordance with the BPMN 2 standard >>> Learn Process modeling best practices with Bonita BPM through live exercises >>> http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ >>> source=Sourceforge_BPM_Camp_5_6_15&utm_medium=email&utm_campaign=VA_SF >>> _______________________________________________ >>> Emc-users mailing list >>> Emc-users@lists.sourceforge.net >>> https://lists.sourceforge.net/lists/listinfo/emc-users > > ------------------------------------------------------------------------------ > BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT > Develop your own process in accordance with the BPMN 2 standard > Learn Process modeling best practices with Bonita BPM through live exercises > http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ > source=Sourceforge_BPM_Camp_5_6_15&utm_medium=email&utm_campaign=VA_SF > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users -- Thanks Rick Lair Superior Roll & Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831 FAX: 734-279-1166 www.superiorroll.com ------------------------------------------------------------------------------ BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15&utm_medium=email&utm_campaign=VA_SF _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users