Well I just checked things with halscope and some keys are working perfectly but others are not.
Another problem I find is that matrix_kb is always sensing row 3/col 1 as true. I unplugged the connector from the P2 port on the 7i73 and the same happens. I have firmware number 14 installed on the board. Jumpers are ok for 8x8 matrix (w5 up and w6 down). Should I upgrade the firmware just to check ? What I find strange is that halscope is detecting the change in the keycode pin. Leonardo Marsaglia El mar., 5 may. 2020 22:56, Peter C. Wallace <[email protected]> escribió: > On Tue, 5 May 2020, Leonardo Marsaglia wrote: > > > Date: Tue, 5 May 2020 22:11:11 -0300 > > From: Leonardo Marsaglia <[email protected]> > > Reply-To: "Enhanced Machine Controller (EMC)" > > <[email protected]> > > To: "Enhanced Machine Controller (EMC)" <[email protected] > > > > Subject: Re: [Emc-users] Mesa 7i73 keypad question/issue > > > > Thank you Peter for your quick response, > > So if I understand correctly, the 7i73.keycode pin is too fast to simply > check it with halmeter by eye. But should I see the changes in halscope? > > > Yes halscope will see any changes > > > El mar., 5 may. 2020 a las 19:41, Peter C. Wallace (<[email protected]>) > escribiяя: > > > On Tue, 5 May 2020, Leonardo Marsaglia wrote: > > > > > Date: Tue, 5 May 2020 19:09:29 -0300 > > > From: Leonardo Marsaglia <[email protected]> > > > Reply-To: "Enhanced Machine Controller (EMC)" > > > <[email protected]> > > > To: "Enhanced Machine Controller (EMC)" < > [email protected] > > > > > > Subject: [Emc-users] Mesa 7i73 keypad question/issue > > > > > > Hello guys, > > > > > > I'm almost done with the config on the Mazak. The last thing I'm trying > > to > > > set up is the front panel keyboard. I'm using a 7i73 wich is already > > > working with the MPG and the lever to move the X and Z axis. > > > > > > The problem I have is, I can't make the keypad input to work. In HAL > I'm > > > always reading the 64 value . I've tried to manually short the pins of > > one > > > column and one row to see if there's any change and nothing. I'm sure > I'm > > > missing something something here, but I didn't want to experiment > without > > > your opinion. > > > > > > I don't know If I'm forgetting to ground something, or to move a > jumper. > > > Anyway, the P2 port of the board is working well. Please let me know > what > > > you think. > > > > > > Thanks as always! > > > > > > > You cannot in general use the keycode as it only reports deltas (and only > > for 1 > > servo thread period) and a no-op code of 64 when idle (no changes) so you > > will > > miss the deltas in hal watch. Normally tye "matrix_kb" component is used > > to > > process the deltas into a static representaion of the keypad state > > > > > > > _______________________________________________ > > > Emc-users mailing list > > > [email protected] > > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > > > > Peter Wallace > > Mesa Electronics > > > > (\__/) > > (='.'=) This is Bunny. Copy and paste bunny into your > > (")_(") signature to help him gain world domination. > > > > > > > > _______________________________________________ > > Emc-users mailing list > > [email protected] > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > _______________________________________________ > Emc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-users > > Peter Wallace > Mesa Electronics > > (\__/) > (='.'=) This is Bunny. Copy and paste bunny into your > (")_(") signature to help him gain world domination. > _______________________________________________ > Emc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-users > _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
