By the way, I forgot to say. The matrix_kb component is not showing the *matrix_kb.**N**.key_rollover *and *matrix_kb.**N**.negative−logic. *
El mié., 6 may. 2020 a las 9:17, Leonardo Marsaglia (<[email protected]>) escribió: > Update. > > I noticed the manual says the following: Note that the component will > only work properly with the version 12 (0xC) 7i73 firmware. > > I suppose the manual is older than firmware 14 but I have to ask, could it > be that I need firmware 12 instead of 14? > > Thank you. > > > El mié., 6 may. 2020 a las 9:01, Leonardo Marsaglia (< > [email protected]>) escribió: > >> Sorry I meant to say I unplugged P1. >> >> El mié., 6 may. 2020 09:00, Leonardo Marsaglia <[email protected]> >> escribió: >> >>> Well I just checked things with halscope and some keys are working >>> perfectly but others are not. >>> >>> Another problem I find is that matrix_kb is always sensing row 3/col 1 >>> as true. I unplugged the connector from the P2 port on the 7i73 and the >>> same happens. I have firmware number 14 installed on the board. Jumpers are >>> ok for 8x8 matrix (w5 up and w6 down). >>> >>> Should I upgrade the firmware just to check ? >>> >>> What I find strange is that halscope is detecting the change in the >>> keycode pin. >>> >>> Leonardo Marsaglia >>> >>> El mar., 5 may. 2020 22:56, Peter C. Wallace <[email protected]> escribió: >>> >>>> On Tue, 5 May 2020, Leonardo Marsaglia wrote: >>>> >>>> > Date: Tue, 5 May 2020 22:11:11 -0300 >>>> > From: Leonardo Marsaglia <[email protected]> >>>> > Reply-To: "Enhanced Machine Controller (EMC)" >>>> > <[email protected]> >>>> > To: "Enhanced Machine Controller (EMC)" < >>>> [email protected]> >>>> > Subject: Re: [Emc-users] Mesa 7i73 keypad question/issue >>>> > >>>> > Thank you Peter for your quick response, >>>> >>>> So if I understand correctly, the 7i73.keycode pin is too fast to simply >>>> check it with halmeter by eye. But should I see the changes in halscope? >>>> >>>> >>>> Yes halscope will see any changes >>>> >>>> >>>> El mar., 5 may. 2020 a las 19:41, Peter C. Wallace (<[email protected]>) >>>> escribiяя: >>>> >>>> > On Tue, 5 May 2020, Leonardo Marsaglia wrote: >>>> > >>>> > > Date: Tue, 5 May 2020 19:09:29 -0300 >>>> > > From: Leonardo Marsaglia <[email protected]> >>>> > > Reply-To: "Enhanced Machine Controller (EMC)" >>>> > > <[email protected]> >>>> > > To: "Enhanced Machine Controller (EMC)" < >>>> [email protected] >>>> > > >>>> > > Subject: [Emc-users] Mesa 7i73 keypad question/issue >>>> > > >>>> > > Hello guys, >>>> > > >>>> > > I'm almost done with the config on the Mazak. The last thing I'm >>>> trying >>>> > to >>>> > > set up is the front panel keyboard. I'm using a 7i73 wich is already >>>> > > working with the MPG and the lever to move the X and Z axis. >>>> > > >>>> > > The problem I have is, I can't make the keypad input to work. In >>>> HAL I'm >>>> > > always reading the 64 value . I've tried to manually short the pins >>>> of >>>> > one >>>> > > column and one row to see if there's any change and nothing. I'm >>>> sure I'm >>>> > > missing something something here, but I didn't want to experiment >>>> without >>>> > > your opinion. >>>> > > >>>> > > I don't know If I'm forgetting to ground something, or to move a >>>> jumper. >>>> > > Anyway, the P2 port of the board is working well. Please let me >>>> know what >>>> > > you think. >>>> > > >>>> > > Thanks as always! >>>> > > >>>> > >>>> > You cannot in general use the keycode as it only reports deltas (and >>>> only >>>> > for 1 >>>> > servo thread period) and a no-op code of 64 when idle (no changes) so >>>> you >>>> > will >>>> > miss the deltas in hal watch. Normally tye "matrix_kb" component is >>>> used >>>> > to >>>> > process the deltas into a static representaion of the keypad state >>>> > >>>> > >>>> > > _______________________________________________ >>>> > > Emc-users mailing list >>>> > > [email protected] >>>> > > https://lists.sourceforge.net/lists/listinfo/emc-users >>>> > > >>>> > >>>> > Peter Wallace >>>> > Mesa Electronics >>>> > >>>> > (\__/) >>>> > (='.'=) This is Bunny. Copy and paste bunny into your >>>> > (")_(") signature to help him gain world domination. >>>> > >>>> > >>>> > >>>> > _______________________________________________ >>>> > Emc-users mailing list >>>> > [email protected] >>>> > https://lists.sourceforge.net/lists/listinfo/emc-users >>>> > >>>> >>>> _______________________________________________ >>>> Emc-users mailing list >>>> [email protected] >>>> https://lists.sourceforge.net/lists/listinfo/emc-users >>>> >>>> Peter Wallace >>>> Mesa Electronics >>>> >>>> (\__/) >>>> (='.'=) This is Bunny. Copy and paste bunny into your >>>> (")_(") signature to help him gain world domination. >>>> _______________________________________________ >>>> Emc-users mailing list >>>> [email protected] >>>> https://lists.sourceforge.net/lists/listinfo/emc-users >>>> >>> _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
