Here's how I did mine:
148-L-N7(su)->show conf lacp
This command shows non-default configurations only.
Use 'show config all' to show both default and non-default configurations.
begin
!
# ***** NON-DEFAULT CONFIGURATION *****
!
!
# lacp
set lacp aadminkey lag.0.48 3984
set lacp singleportlag enable
!
end
set port lacp port ge.2.70 aadminkey 3984
set port lacp port ge.2.71 aadminkey 3984
set port lacp port ge.6.70 aadminkey 3984
set port lacp port ge.6.71 aadminkey 3984
set port lacp port ge.2.70 padminkey 3984
set port lacp port ge.2.71 padminkey 3984
set port lacp port ge.6.70 padminkey 3984
set port lacp port ge.6.71 padminkey 3984
clear port lacp port ge.2.70 aadminstate lacpactive
clear port lacp port ge.2.71 aadminstate lacpactive
clear port lacp port ge.6.70 aadminstate lacpactive
clear port lacp port ge.6.71 aadminstate lacpactive
set port lacp port ge.2.70 padminstate lacpagg
set port lacp port ge.2.71 padminstate lacpagg
set port lacp port ge.6.70 padminstate lacpagg
set port lacp port ge.6.71 padminstate lacpagg
set port lacp port ge.2.70 disable
set port lacp port ge.2.71 disable
set port lacp port ge.6.70 disable
set port lacp port ge.6.71 disable
148-L-N7(su)->show port stat ge.2.70;ge.2.71;ge.6.70-71
Port Alias Oper Admin Speed Duplex Type
(truncated) Status Status (bps)
------------ ---------------- -------- ------- ------ ------- ------------------
ge.2.70 dormant up 1.0G full 1000-t rj45
ge.2.71 dormant up 1.0G full 1000-t rj45
ge.6.70 dormant up 1.0G full 1000-t rj45
ge.6.71 dormant up 1.0G full 1000-t rj45
4 of 4 ports displayed, 4 port(s) with oper status 'up' or 'dormant'.
148-L-N7(su)->
148-L-N7(su)->show port stat lag.0.48
Port Alias Oper Admin Speed Duplex Type
(truncated) Status Status (bps)
------------ ---------------- -------- ------- ------ ------- ------------------
lag.0.48 up up 4.0G lag
1 of 1 ports displayed, 1 port(s) with oper status 'up' or 'dormant'.
Thanks,
Lou Goddard
Network Engineer
302-552-8053
[email protected]
From: "Greer, Paul" <[email protected]>
Sent: Thu, 9/30/2010 2:13pm
To: Enterasys Customer Mailing List <[email protected]>
Subject: [enterasys] LACP
I have lags working between two buildings (N3 to C3) but I ran into some issue
when I connected two N3's.
One port shows up on the lag but when I connect the other port the N3's drop
connections.
Is there something unique about the two N3's being connected?
I have followed the config guide from the Enterasys Document page for multiple
devices as a template.
The config for all Lags appear to be the same and correct.
Paul
Paul Greer
Information Technology Services
South Puget Sound Community College
2011 Mottman Rd Sw
Olympia, WA 98512
360-596-5324
[email protected]
--To unsubscribe from enterasys, send email to [email protected] with the body:
unsubscribe enterasys [email protected]
------------------ CONFIDENTIALITY NOTICE ---------------
This message, including any attachments, is for the sole use of the
intended recipient(s) and may contain privileged confidential information
protected by law. Any unauthorized review, use, disclosure or distribution
of this message is prohibited. If you are not the intended recipient, please
contact the sender by reply e-mail and destroy all copies of this message.
------------------ CONFIDENTIALITY NOTICE ---------------
--------
This message has been scanned for viruses and dangerous content by
MailScanner, and is believed to be clean.
---
To unsubscribe from enterasys, send email to [email protected] with the body:
unsubscribe enterasys [email protected]
