In our electrical work in electronics labs and comm rooms, we do a lot of RF 
shielding, isolated grounding systems.  I apply this same science to my EV 
back in 1980.  Aircraft use this type of isolated and shielding system.

All communication circuits which includes rpm sensor, E-meter, shunts and 
speaker wires are all double shield.  The internal shield only grounds at 
the senders and device chassis leaving the other end of the shield floating. 
The external shield is only grounded at the other end to a chassis plate 
that use insulated standoffs that mount to a steel equipment box that houses 
the Z1K and all related devices.

The contactors, fuses, and charger meters are install in the rear of the EV 
on separated aluminum chassis plates on insulated standoffs inside either 
cast aluminum or fiberglass equipment boxes.

A counter poise grounding circuit coming from the B- or a 12 volt accessory 
battery runs around the total perimeter of the EV in a complete circle which 
is then connected to the B- again.

This counter poise ground wire must be larger than all the combined ground 
circuits in the EV.  Tap offs this counter poise is from a cadmium plated 
metal standoff using threaded rod couplers that screw in to the existing EV 
body bolt connections.  Use a spade wire terminal to bolt the counter poise 
wire at every tap off.

The counter poise circuits uses a No. 1 AWG copper stranded and No. 6 AWG 
copper stranded for the tap offs.  Two No. 6 wire connects to the fire wall 
and two No. 8 AWG copper stranded wire taps off the No. 6 using a standoff 
that grounds to the any equipment boxes and internal chassis plates.  A No. 
10 AWG copper stranded wire than taps off the No. 8 wire connection on the 
equipment box and/or chassis plate.

The a No. 10 wire is connected to the No. 8 wire junction point on the 
chassis to the mounting feet of the motor controller and any other devices 
use with the motor controller.

This is continuous ground path of the B- 12 volt circuit.  If your EV is a 
steel body that uses self grounding devices or ground wires tap to the body, 
this may be the cause of your static noise.  Do not relied on the vehicle 
body for a return ground.

I also install all wiring circuits of different voltages and comm wires in a 
steel wire way that runs through the center of the vehicle from the front 
fire wall, through a center fire to the rear equipment panels. Instead of 
wireways, you can use aluminum flexible conduit or double shield cables.

Also if you combined different voltages circuits bundle together or in a 
conduit or wire way, the insulation of all the wires, must be voltage rated 
at the highest voltage circuit.

In all my wire circuits, I prefer to use a 600 volt rating wire type THW 90 
degree C. rated, 19 or 39 stranded copper. You can use THWN which has a 
extra nylon jacket, but is normally use for ease in pulling in a conduit. 
The THW has a thicker and softer insulation design for chassis work.

I do not get any noise on FM and only some light noise on the AM at very low 
motor rpm of less 100 rpm.  After 100 rpm, the AM noise go's away.

Roland


----- Original Message ----- 
From: "Rob Trahms" <[email protected]>
To: <[email protected]>
Sent: Friday, May 24, 2013 10:41 PM
Subject: [EVDL] Here's an interesting issue: FM interference BEFORE motor on


> Hi all -
>
> 1989 VW Cabriolet
> Cafe Electric Z1K motor controller
> Impulse9 motor
>
> I have been digging into my EV radio interference problem again, and 
> tonight
> discovered a very interesting distinction between AM and FM radio in the 
> EV.
>
> AM radio is predictably unusable when the motor is engaged, and it does in
> fact get worse with higher RPMs.
>
> While I previously thought FM radio was the same, I was incorrect.  FM
> signal is decent with the ignition in position 1 (where you can remove the
> key), but position 2 (just prior to ignition) a general static noise 
> starts
> and grows louder until drowning out the FM signal entirely.  There is no
> difference after ignition - interesting!
>
> What this tells me is that the motor has little or nothing to do with the 
> FM
> interference I am experiencing!
> I am now optimistic I can solve this, at least on the FM side of things.
>
> The working theory I have is that either the Hairball microcontroller or
> possibly the aux voltage gauge is generating the FM noise (seems unlikely
> that it would be the TBS e-meter I have, because that is on all the time,
> even when the ignition is off).
>
> Other theories on why I am seeing FM noise?
>
> Thanks in advance!
> Rob
>
>
>
>
> -----
> Electro, the Cabby-EV
> http://chaosmgmt.blogspot.com
> http://www.evalbum.com/1426
> --
> View this message in context: 
> http://electric-vehicle-discussion-list.413529.n4.nabble.com/Here-s-an-interesting-issue-FM-interference-BEFORE-motor-on-tp4663203.html
> Sent from the Electric Vehicle Discussion List mailing list archive at 
> Nabble.com.
> _______________________________________________
> UNSUBSCRIBE: http://www.evdl.org/help/index.html#usub
> http://lists.evdl.org/listinfo.cgi/ev-evdl.org
> For EV drag racing discussion, please use NEDRA 
> (http://groups.yahoo.com/group/NEDRA)
>
> 
_______________________________________________
UNSUBSCRIBE: http://www.evdl.org/help/index.html#usub
http://lists.evdl.org/listinfo.cgi/ev-evdl.org
For EV drag racing discussion, please use NEDRA 
(http://groups.yahoo.com/group/NEDRA)

Reply via email to