A lot of car radios use a ground strap connecting to the frame/body of a 
vehicle.  That is a lot of resistance for the ground path to the a B- 12 
volt ground source.  I first connect a 12 volt B- directly to the radio case 
and see what happens.

My radio is a Sony that slides into a second steel case which makes it easy 
to remove the radio by unlatching it with a security key.  The steel case 
has a large steel case capacitor that is connected to this steel radio case 
and to a good ground source to B- of a battery.
The capacitor is a ignition capacitor that is use in distributors in a ICE 
vehicle.

The steel enclosure acts as a Faraday shield for many isolated electrical 
and communication devices.

With the 12 volt ignition switch off, take a voltage reading across the 
battery terminals.  Lets say it reads 13.3 volts just after you turn off the 
ignition switch removing a charging source.  Wait about 10 to 12 hours and 
the voltage may drop to about 12.8 volts which is normal.

Then connect the volt meter leads from the positive at the battery and a 
grounding strap for a device on the fire wall or in the dash.  I have seen 
up to 1 to 2 volt drop which is cause by the high resistance of the steel 
body parts.

Sometimes a fuse clip, fuses or circuit breaker may cause a voltage drop on 
the B+ side of the battery which may cause noise.

Roland




----- Original Message ----- 
From: "Rob Trahms" <[email protected]>
To: <[email protected]>
Sent: Saturday, May 25, 2013 9:01 AM
Subject: Re: [EVDL] Here's an interesting issue: FM interference BEFOREmotor 
on


> Wow, thanks Roland.  That is some thorough shielding!  I am probably not
> going to replace all of my wiring at this point to solve this problem 
> though
> - just the offending culprit.
>
> It definitely seems like it is something fairly simple, because my FM 
> radio
> works fantastic when the key is out (and by the way, the E-meter 
> (including
> pack voltage, shunt measurements) and Hairball are running all the time, 
> so
> they do not cause a problem at this point).
>
> When the key is turned to pre-ignition position, this is typically where 
> all
> standard auxiliary electronics in the car go on, including the auxiliary
> voltmeter in the dash.  THIS is when the FM static starts.  The motor
> contactor isn't even engaged at this point, so the motor and controller 
> are
> out of the picture.  Interestingly, AM still sounds good at this point,
> probably because the interference source is more in the FM band and not in
> AM.
>
> My thinking one of the following culprits:
> 1) Either my radio isn't properly grounded, or
> 2) My antenna cable isn't properly shielded, or
> 3) One of my aux circuits needs a shield.
>
> Does this sound right?
>
> Rob
>
>
>
> -----
> Electro, the Cabby-EV
> http://chaosmgmt.blogspot.com
> http://www.evalbum.com/1426
> --
> View this message in context: 
> http://electric-vehicle-discussion-list.413529.n4.nabble.com/Here-s-an-interesting-issue-FM-interference-BEFORE-motor-on-tp4663203p4663216.html
> Sent from the Electric Vehicle Discussion List mailing list archive at 
> Nabble.com.
> _______________________________________________
> UNSUBSCRIBE: http://www.evdl.org/help/index.html#usub
> http://lists.evdl.org/listinfo.cgi/ev-evdl.org
> For EV drag racing discussion, please use NEDRA 
> (http://groups.yahoo.com/group/NEDRA)
>
> 
_______________________________________________
UNSUBSCRIBE: http://www.evdl.org/help/index.html#usub
http://lists.evdl.org/listinfo.cgi/ev-evdl.org
For EV drag racing discussion, please use NEDRA 
(http://groups.yahoo.com/group/NEDRA)

Reply via email to