I'm attempting to get my Smart&Friendly CD-RW 226 set up under Mandrake 6.1. I'm having problems getting the included isa scsi card working (I think it's an adaptec aha-1515 or aha-1510). I've been digging around, & I think I've found the options I'm supposed to feed it to get it working (aha152x=0x340,9,7,1), but the system never detects the card on boot. If I run 'cdrecord -scanbus' it detects the card & the attached CD-RW, but then begins spitting a bunch of error messages out to the screen. The only part of it I've managed to catch is something about the card being reset because of a timeout or something. I've attached a chunk of the output when I run cdrecord -scanbus, stopping where it seems to start repeating.
Oct 10 14:13:42 twain kernel: aha152x: BIOS test: passed, detected 1 controller(s) Oct 10 14:13:42 twain kernel: aha152x0: vital data: PORTBASE=0x340, IRQ=9, SCSI ID=7, reconnect=enabled, parity=enabled, synchronous=disabled, delay=100, extended translation=disabled Oct 10 14:13:42 twain kernel: aha152x: trying software interrupt, ok. Oct 10 14:13:42 twain kernel: scsi0 : Adaptec 152x SCSI driver; $Revision: 1.7 $ Oct 10 14:13:42 twain kernel: scsi : 1 host. Oct 10 14:13:45 twain kernel: scsi : aborting command due to timeout : pid 6, scsi0, channel 0, id 6, lun 0 Test Unit Ready 00 00 00 00 00 Oct 10 14:13:45 twain kernel: aha152x: abort(), SCpnt=0x807ffe00, QUEUE STATUS: Oct 10 14:13:46 twain kernel: issue_SC: Oct 10 14:13:46 twain kernel: current_SC: Oct 10 14:13:46 twain kernel: 0x807ffe00: target=6; lun=0; cmnd=(Test Unit Ready 00 00 00 00 00 Oct 10 14:13:46 twain kernel: ); residual=256; buffers=0; phase |send_ident|; in other(COMMAND); phaseend; next=0x00000000 Oct 10 14:13:46 twain kernel: disconnected_SC: Oct 10 14:13:46 twain kernel: Oct 10 14:13:46 twain kernel: on bus: SCSISEQ (); SCSISIG (STATUS); INTSTAT (hi); SSTAT (SELDO PHASEMIS PHASECHG REQINIT ); SSTAT (PHASEMIS ); SXFRCTL0 (CH1 ); SIGNAL (BSYI REQI ); SELID (00), SSTAT2 (SEMPTY ); SFCNT (0); SCSICNT (0), OFFCNT(0), SSTAT4 (); DMACNTRL0 (16BIT PIO READ ); DMASTAT (DFIFOEMP ) Oct 10 14:13:46 twain kernel: enabled interrupts (ENPHASEMIS ENBUSFREE ) Oct 10 14:13:47 twain kernel: Vendor: SAF Model: CD-RW226 Rev: 1.12 Oct 10 14:13:47 twain kernel: Type: CD-ROM ANSI SCSI revision: 02 Oct 10 14:13:47 twain kernel: Detected scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0 Oct 10 14:13:49 twain kernel: scsi0 channel 0 : resetting for second half of retries. Oct 10 14:13:49 twain kernel: SCSI bus is being reset for host 0 channel 0. Oct 10 14:13:58 twain kernel: scsi : aborting command due to timeout : pid 8, scsi0, channel 0, id 6, lun 1 Test Unit Ready 20 00 00 00 00 Oct 10 14:13:58 twain kernel: aha152x: abort(), SCpnt=0x807ffe00, QUEUE STATUS: Oct 10 14:13:58 twain kernel: issue_SC: Oct 10 14:13:58 twain kernel: 0x807ffe00: target=6; lun=1; cmnd=(Test Unit Ready 20 00 00 00 00 Oct 10 14:13:58 twain kernel: ); residual=256; buffers=0; phase |not issued|; next=0x00000000 Oct 10 14:13:58 twain kernel: current_SC: Oct 10 14:13:58 twain kernel: none Oct 10 14:13:58 twain kernel: disconnected_SC: Oct 10 14:13:58 twain kernel: Oct 10 14:13:58 twain kernel: waiting: SCSISEQ (); SCSISIG (DATA OUT); INTSTAT (hi); SSTAT (BUSFREE ); SSTAT (BUSFREE ); SXFRCTL0 (CH1 ); SIGNAL (); SELID (00), SSTAT2 (SEMPTY ); SFCNT (0); SCSICNT (0), OFFCNT(0), SSTAT4 (); DMACNTRL0 (16BIT PIO READ ); DMASTAT (DFIFOEMP ) Oct 10 14:13:58 twain kernel: enabled interrupts (ENBUSFREE ) Oct 10 14:14:04 twain kernel: scsi : aborting command due to timeout : pid 8, scsi0, channel 0, id 6, lun 1 Test Unit Ready 20 00 00 00 00 Oct 10 14:14:04 twain kernel: aha152x: abort(), SCpnt=0x807ffe00, QUEUE STATUS: Oct 10 14:14:04 twain kernel: issue_SC: Oct 10 14:14:04 twain kernel: 0x807ffe00: target=6; lun=1; cmnd=(Test Unit Ready 20 00 00 00 00 Oct 10 14:14:04 twain kernel: ); residual=256; buffers=0; phase |not issued|; next=0x00000000 Oct 10 14:14:04 twain kernel: current_SC: Oct 10 14:14:04 twain kernel: none Oct 10 14:14:04 twain kernel: disconnected_SC: Oct 10 14:14:04 twain kernel: Oct 10 14:14:04 twain kernel: waiting: SCSISEQ (); SCSISIG (DATA OUT); INTSTAT (hi); SSTAT (BUSFREE ); SSTAT (BUSFREE ); SXFRCTL0 (CH1 ); SIGNAL (); SELID (00), SSTAT2 (SEMPTY ); SFCNT (0); SCSICNT (0), OFFCNT(0), SSTAT4 (); DMACNTRL0 (16BIT PIO READ ); DMASTAT (DFIFOEMP ) Oct 10 14:14:04 twain kernel: enabled interrupts (ENBUSFREE ) Oct 10 14:14:09 twain PAM_pwdb[2837]: (su) session opened for user root by (uid=0) Oct 10 14:14:27 twain PAM_pwdb[2822]: (su) session closed for user root Oct 10 14:14:34 twain kernel: scsi : aborting command due to timeout : pid 9, scsi0, channel 0, id 6, lun 0 Mode Sense 00 2a 00 80 00
