Your procedure worked! Thank you. Toshiro.
El mié, 06-11-2002 a las 13:09, Simon Ree escribió: > I have found that binding to ttyUSB1 will not work until the > port is created and destroyed once prior to hotsync and not > before pilot-link has had an initial connection. > > My method after clean install of Mandrake (only has to be > done once) > > 1. command line > 2. plug in and press hotsync > 3. let the device time out, clear error on device > 4. press hotsync > 5. pilot-xfer -p ttyUSB1 -b /home/me/clie/backup > > After a successful backup (hopefully), run jpilot and set > the port up in preferences /dev/ttyUSB1. Close jpilot, > press sync on the device and open jpilot and press sync... > should work. > > I have found on all syncs after the initial sync that jpilot > will not communicate with my clie until the device times out > once. > > 1. press sync on the device/cradle and let it time out > 2. press sync again and then open jpilot and press sync > > Support should be better than this but the what can you do. > > Let me know if it works for you. This method works on my 3 > different machines. > > Regards, > > Simon Ree > [EMAIL PROTECTED] > > On 05 Nov 2002 21:30:28 -0300 > Toshiro <[EMAIL PROTECTED]> wrote: > > > The model is PEG-N760C (PalmOS 4.1). > > > > Here's the output of dmesg: > > > > usbserial.c: Sony Clié 4.x converter detected > > visor.c: Sony Clié 4.x: Number of ports: 2 > > visor.c: Sony Clié 4.x: port 1, is for Generic use and is > > bound to ttyUSB0 > > visor.c: Sony Clié 4.x: port 2, is for HotSync use and is > > bound to ttyUSB1 > > usb-uhci.c: interrupt, status 2, frame# 303 > > usbserial.c: Sony Clié 4.x converter now attached to > > ttyUSB0 (or usb/tts/0 for devfs > > ) > > usbserial.c: Sony Clié 4.x converter now attached to > > ttyUSB1 (or usb/tts/1 for devfs > > ) > > visor.c: Device lied about number of ports, please use a > > lower one. visor.c: Device lied about number of ports, > > please use a lower one. visor.c: Device lied about number > > of ports, please use a lower one. visor.c: Device lied > > about number of ports, please use a lower one. visor.c: > > Device lied about number of ports, please use a lower one. > > visor.c: Device lied about number of ports, please use a > > lower one. visor.c: Device lied about number of ports, > > please use a lower one. > > > > The versions are: > > j-pilot 0.99.2 > > pilot-xfer 0.11.3 > > > > Regards, > > Toshiro. > > > > > > > > What model? My clie T415 works fine with the USB > > > cradle. What does dmesg say when you plug it in and hit > > > the hotsync? What version of jpilot and pilot-xfer? > > > > > > Regards, > > > > > > Simon Ree > > > [EMAIL PROTECTED] > > > > > > On 02 Nov 2002 15:44:39 -0300 > > > Toshiro <[EMAIL PROTECTED]> wrote: > > > > > > > Anybody know how to synchronize a Sony Clié PDA (it's > > > > Palm compatible, running Palm OS 4.1) in Mandrake? > > > > > > > > The cradle is USB, and the device is not recognized > > > > (no/dev/ttyUSBx). > > > > > > > > Do I have to recompile the kernel? > > > > > > > > > > > > ---- > > Want to buy your Pack or Services from MandrakeSoft? > Go to http://www.mandrakestore.com
Want to buy your Pack or Services from MandrakeSoft? Go to http://www.mandrakestore.com