Hello,
Attached my targetcli output...looks good?
Whats the next step? How to setup the initiator and establish the
connection?
# targetcli
targetcli shell version 2.0rc1.fb16
Copyright 2011 by RisingTide Systems LLC and others.
For help on commands, type 'help'.
/> ls
o- /
..........................................................................
........................................ [...]
o- backstores
..........................................................................
............................. [...]
| o- block
..........................................................................
................... [1 Storage Object]
| | o- Disk1
....................................................................
[/dev/sdb1 (2.0GiB) write-back activated]
| o- fileio
..........................................................................
.................. [0 Storage Object]
| o- pscsi
..........................................................................
................... [0 Storage Object]
o- loopback
..........................................................................
......................... [0 Targets]
o- tcm_fc
..........................................................................
........................... [2 Targets]
o- 10:00:90:e2:ba:3d:38:82
..........................................................................
.......... [enabled]
| o- acls
..........................................................................
............................. [0 ACL]
| o- luns
..........................................................................
............................. [1 LUN]
| o- lun0
..........................................................................
......... [block/Disk1 (/dev/sdb1)]
o- 20:00:90:e2:ba:3d:38:82
..........................................................................
.......... [enabled]
o- acls
..........................................................................
............................. [0 ACL]
o- luns
..........................................................................
............................. [1 LUN]
o- lun0
..........................................................................
......... [block/Disk1 (/dev/sdb1)]
-----Original Message-----
From: Love, Robert W [mailto:[email protected]]
Sent: Thursday, August 08, 2013 5:51 PM
To: Gerald Stanje; Patil, Kiran; [email protected]
Subject: RE: example
> From: Gerald Stanje [mailto:[email protected]]
> Sent: Thursday, August 08, 2013 5:47 PM
> To: Love, Robert W; Patil, Kiran; [email protected]
> Subject: RE: example
>
> Here the output:
>
>
>
> [root@promd-1n-dhcp2-dhcp411 fcoe_scripts]# modprobe fcoe
> [root@promd-1n-dhcp2-dhcp411 fcoe_scripts]# echo eth2 >
> /sys/module/libfcoe/parameters/create_vn2vn
> [root@promd-1n-dhcp2-dhcp411 fcoe_scripts]# fcoeadm -i
> Description: 82599EB 10-Gigabit SFI/SFP+ Network Connection
> Revision: 01
> Manufacturer: Intel Corporation
> Serial Number: 90E2BA3D3880
> Driver: ixgbe 3.9.15-k
> Number of Ports: 1
>
> Symbolic Name: fcoe v0.1 over eth2
> OS Device Name: host6
> Node Name: 0x100090E2BA3D3882
> Port Name: 0x200090E2BA3D3882
Above is the WWN to use in targetcli, remember it's particular about the
case, so try lower if upper doesn't work and I think you drop the '0x'.
> FabricName: 0x0000000000000000
> Speed: 10 Gbit
> Supported Speed: 1 Gbit, 10 Gbit
> MaxFrameSize: 2112
> FC-ID (Port ID): 0x003882
> State: Online
>
>
> fcoe is ready to go?
>
FCoE is up and running on that port.
Aside from the port being "Online," you can see that a FC-ID has also been
chosen- an indication that the port gone through the FIP VN2VN FC-ID
discovery process.
//Rob
_______________________________________________
fcoe-devel mailing list
[email protected]
http://lists.open-fcoe.org/mailman/listinfo/fcoe-devel
