Installed perfectly. Runs perfectly. Thanks to you and all the crew! Bill
On Fri, Jul 22, 2011 at 6:48 PM, Greg Jurrens <[email protected]> wrote: > Dear FlexRadio customers: > > > FlexRadio is pleased to announce the new Official Release of PowerSDR(TM) > v2.1.5 is now available for immediate download from our website. > > PowerSDR 2.1 adds significant feature and performance enhancements over the > prior official release to all models including the FLEX-5000A, FLEX-5000C, > FLEX-VU5K upgrades, FLEX-3000, FLEX-1500, and SDR-1000. We recommend that > all customers upgrade to v2.1.5. > > The files can be downloaded at: > > PowerSDR v2.1.5 Integrated Installer / Setup Suite: > http://support.flex-radio.com/Downloads.aspx?id=371 > > PowerSDR 2.1.5 Release Notes: > http://support.flex-radio.com/Downloads.aspx?id=372 > > > While the improvements are too numerous to detail, the following is a list > of major changes since the previous official release, PowerSDR v2.0.22: > > > > 1. There is now an optional installation of the new FlexControl™ driver. > Important: Please read the FlexControl Installation Errata Sheet regarding > FlexControl use with Virtual Serial Port software. > > 2. FM has been completely redesigned including CTCSS tones, improved > modulation/demodulation, soft limiting, FM squelch and more. > > 3. FM now has a dedicated Repeater Mode that allows you to set positive and > negative offsets along with the frequency offset. Split mode is no longer > needed to operate FM repeaters. For more information, refer to the KB > article How to Use FM Repeater Mode ( > http://kc.flexradio.com/KnowledgebaseArticle50501.aspx) > > 4. We've added a new and improved MEMORY form that integrates with the new > FM Repeater Mode. For more information, refer to the KB article How to Use > the Memory Form (http://kc.flexradio.com/KnowledgebaseArticle50500.aspx) > > 5. FM mode has a new mode specific control panel that allows you to select > Memory channels from the console. > > 6. Full duplex when receiving on VFOA when transmitting on VFOB is now > supported. Previously, full duplex was only supported when receiving on > VFOB while transmitting on VFOA. This feature is usefule for SO2R on the > FLEX-5000 and satellite cross-band duplex on the FLEX-5000 with FLEX-VU5K > installed. > > 7. Added FLEX-5000 RX2 wave record/playback. > > 8. A Remove button (red X) is now provided on the Radio Chooser panel to > allow easier radio start up maintenance. > > > Thanks to so many of you who have continued to provide constructive > feedback > during the development process. We would like to express our special > appreciation to our internal alpha/beta team for their tireless testing of > internal releases. > > > Enjoy, > > Greg > > > -- > Greg Jurrens - K5GJ > VP, Sales and Marketing > FlexRadio Systems > 4616 W Howard Lane Ste 1-150 > Austin, TX 78728 > T: 512-535-4713 x203 > E: [email protected] > SKYPE: WD0ACD > “Tune in Excitement” ™ > > PowerSDR(TM) is a trademark of FlexRadio Systems > _______________________________________________ > FlexRadio Systems Mailing List > [email protected] > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ > Knowledge Base: http://kc.flexradio.com/ Homepage: > http://www.flexradio.com/ > _______________________________________________ Flexedge mailing list [email protected] http://mail.flex-radio.biz/mailman/listinfo/flexedge_flex-radio.biz This is the FlexRadio Systems e-mail Reflector called FlexEdge. It is used for posting topics related to SDR software development and experimentalist who are using beta versions of the software.
