Upon further investigation I have found that any change (ie: change power, push another button) on the console will disable break in & ptt when in cw mode. Also the power output is always full power no mater what the console is set at in cw, which sucks if you run an amp. Stop the console and restart or toggle VAC fixes it. It is the same on all bands. I will try to see what version it broke in.
Dave - N4DWK Mark Amos wrote: > I'm having a similar problem just using the internal CWX keyer. Works once > after starting or after > VAC On/Off then stops. Makes for short QSO's... Worked fine this morning on > 40 - I'm pretty sure > that was before updating to 1738. I'll just listen for a while! > > Mark > W8XR > > > > Due to the fact that it is not present in earlier SVN versions it is probably > a bug, and I have > submitted it as such. > > By the way my keyer (Microham CW Keyer) is plugged directly into the Flex key > jack, and I do not > have iambic mode enabled. > > Kirb Nesbitt wrote: > >> This is likely all related; >> As of svn 1738 break-in on cw ceases to function unless the VAC button >> is selected and then de-selected, or the console is powered off/on. >> The radio works for a short period and then spontaneously quits >> transmitting (no t/r). Eric's been working on this over the last several svn >> releases. >> This problem is present when keying via the PC Com port (ext. keyer), >> or directly into the "key" input on the radio. >> I'm also curious to know others experiences using a paddle plugged >> directly into the radio's "key" jack (keying> iambic mode) with the >> last few svn releases? >> >> 73, >> >> Kirb - VE6IV >> -- >> >> >> >>> I >>> don't know if anyone else has this problem. >>> >>> If I switch to cw from ssb, or the other way, the ptt or break in do >>> not work. >>> If I stop SDR and restart all comes back ok. As soon as I switch >>> between cw and ssb again it quits. It is very consistent on 160-40m, >>> not so much above 30m. >>> Vox works no matter what happens, but it won't key with the key or >>> ptt. >>> I'm using SVN 1738, I tried an older version like 1730 and it >>> doesn't do this. >>> Is it a bug? or just me. >>> >>> Dave Kiefer - N4DWK >>> >>> >> _______________________________________________ >> FlexRadio mailing list >> FlexRadio@flex-radio.biz >> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz >> Archive Link: http://www.mail-archive.com/flexradio%40flex-radio.biz/ >> FlexRadio Knowledge Base: http://kb.flex-radio.com/ FlexRadio >> Homepage: http://www.flex-radio.com/ >> >> >> >> >> > > _______________________________________________ > FlexRadio mailing list > FlexRadio@flex-radio.biz > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz > Archive Link: http://www.mail-archive.com/flexradio%40flex-radio.biz/ > FlexRadio Knowledge Base: http://kb.flex-radio.com/ FlexRadio Homepage: > http://www.flex-radio.com/ > > > > > _______________________________________________ > FlexRadio mailing list > FlexRadio@flex-radio.biz > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz > Archive Link: http://www.mail-archive.com/flexradio%40flex-radio.biz/ > FlexRadio Knowledge Base: http://kb.flex-radio.com/ > FlexRadio Homepage: http://www.flex-radio.com/ > > > > _______________________________________________ FlexRadio mailing list FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archive Link: http://www.mail-archive.com/flexradio%40flex-radio.biz/ FlexRadio Knowledge Base: http://kb.flex-radio.com/ FlexRadio Homepage: http://www.flex-radio.com/