On Sat, Jun 14, 2008 at 6:36 PM, Tim Ellison <[EMAIL PROTECTED]> wrote: > There have been a few reports of the RX2 not completing the RX2 calibrations > listed in the install instructions. Eric and the crew are aware of it and > are working to resolve it. > > My RX2 has this problem too. :-( > > You can try the following. > > Download the latest version of PowerSDR in /branches/test. Checkout > (download) the entire folder and place it into a newly created folder. Do > not use a folder that previously contained the PowerSDR program files. You > want to download ALL of the files from the branches/test/bin/Release so that > all of the files are refreshed. > > Start PowerSDR which will run the Wisdom configurator and create a brand new > database. Configure *only* the sampling rate and audio buffers (96 KHz > /1024). Leave all other parameters in the database at their defaults. > > Connect a dummy load to ANT1. Disconnect all other antennas (including RX2 > in) > > Open the Antenna Selection applet and set it for simple mode, RX1 = ANT1, RX2 > = RX1 TAP and TX = ANT1. Select the check box to lock RX and TX to the same > antenna. Do not check the box to use the RX1 In/ RX1/Out loop > > Run the RX2 level calibration test. After the test wait a few seconds to > make sure the EEPROM is completely updated. If that passes, run the RX2 > image calibration test. > > Good luck! > > -Tim > > -----Original Message----- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Mark Mumaw > Sent: Saturday, June 14, 2008 5:52 PM > To: FlexRadio reflector > Subject: [Flexradio] RX2 Problem-Help > > I installed RX2 yesterday but cannot get a successful Level Calibration on > all bands. One or more bands always fail but not always the same bands. I > have tried recreating .mdb file. I have tried with a dummy load and no > antenna. I am using PowerSDR 1.12.0 with 1.2.0.0 firmware. > > > > The receiver is basicly working but with sensitivity and image issues. > > > > I will call customer support on Monday but I'm hoping someone has some ideas > of something to try. > > > > Any ideas??????? > > > > 73's Mark NU6X Sedona, AZ > > _______________________________________________ > FlexRadio Systems Mailing List > [email protected] > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ > Knowledge Base: http://kb.flex-radio.com/ Homepage: > http://www.flex-radio.com/ > > > _______________________________________________ > FlexRadio Systems Mailing List > [email protected] > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ > Knowledge Base: http://kb.flex-radio.com/ Homepage: > http://www.flex-radio.com/ > >
I also found that in some cases just a few bands will not pass, so just rerun the test and select those bands. -- Neal Campbell Abroham Neal Software Programming Services for Windows, OS X and Linux (540) 242 0911 --------------------------------------------------------------------- Try Spot for OS X, the intelligent DXCluster Client at www.abrohamnealsoftware.com - introduction priced at $10.99 ------------------------------------------------- For a great dog book, visit www.abrohamneal.com ------------------------------------------------- See the FlexRadio Systems Flex-5000a in action at www.flex-videos.com _______________________________________________ FlexRadio Systems Mailing List [email protected] http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kb.flex-radio.com/ Homepage: http://www.flex-radio.com/
