Second try, because i used a wrong orginator email adress....
Hello Tim, > > i checked ist more detailed and found with stopping the time it is on all > bands the same. The PTT noise of the FLEX-1500 is hearable direct after > entering a macro. But the needle of the power/SDR meter starts moving > exactly after 5.7 seconds on all bands. I do not use ddutil but VCom. The > rigcontrol is via Com 7 and PTT i tried seperate COM port with hardware PTT > in FLDIGI or without. With harware PTT no delay is set up.Without hardware > PTT it is all the same. > > Regards > Mathias > > 2012/3/2 Tim Ellison, W4TME <t...@flex-radio.com> > > Are you 100% certain that the radio is not being keyed immediately or is >> the radio being keyed immediately and there is a delay generating the digi >> mode tones and hence the RF? >> >> PowerSDR does not differentiate between bands when issuing the TX or ZZTX >> CAT command to key the radio, so I'd look at Fldigi or any other process >> you have in line (are you using DDUtil?) like the virtual com port software >> as the possible sources of the problem since it works well on 20m and not >> on 40m. >> >> BTW, I have Fldigi setup using RigCAT to communicate with PowerSDR and to >> assert PTT (as opposed to the "bit bang" serial port) and I do not see >> these delays. >> >> Tim Ellison, W4TME >> Product Management, Sales & Support >> FlexRadio Systems^(TM) >> 4616 W Howard Ln, Suite 1-150 >> Austin, TX 78728 >> Phone: 512-535-4713 Ext. 223 >> Email: t...@flexradio.com <mailto:t...@flexradio.com> >> Web: www.flexradio.com <http://www.flexradio.com> >> >> logo >> >> >> >> On 3/2/2012 1:40 AM, Mathias Krueger wrote: >> >>> Hello, >>> >>> I work for about 4 week in BPSK31 with FLDIGI and my Flex-1500. I found >>> a delay difference e.g. between 20m and 40m. In 20m the tx starts quite >>> direct if i click a macro or the tx button in FLDIGI. In 40m is a delay of >>> about 2s. The PTT switch behavior is the same on 20 and 40. But in 40 there >>> is no HF out until the 2 seconds are over... What could be the problem? Any >>> solution available? >>> >>> Thanks in advance. >>> Regards >>> Mathias >>> HB9DOU >>> >>> >>> >>> ______________________________**_________________ >>> FlexRadio Systems Mailing List >>> FlexRadio@flex-radio.biz >>> http://mail.flex-radio.biz/**mailman/listinfo/flexradio_**flex-radio.biz<http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz> >>> Archives: >>> http://www.mail-archive.com/**flexradio%40flex-radio.biz/<http://www.mail-archive.com/flexradio%40flex-radio.biz/> >>> Knowledge Base: http://kc.flexradio.com/ Homepage: >>> http://www.flexradio.com/ >>> >> ______________________________**_________________ >> FlexRadio Systems Mailing List >> FlexRadio@flex-radio.biz >> http://mail.flex-radio.biz/**mailman/listinfo/flexradio_**flex-radio.biz<http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz> >> Archives: >> http://www.mail-archive.com/**flexradio%40flex-radio.biz/<http://www.mail-archive.com/flexradio%40flex-radio.biz/> >> Knowledge Base: http://kc.flexradio.com/ Homepage: >> http://www.flexradio.com/ >> > > _______________________________________________ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/