Tim,
I found the problem. After the upgrade Skimmer decided to use VAC 3&4
instead of 1&2. Once this was changed it started to work. I don't know
why Skimmer picked the different audio channels but it happened. Thanks
for looking at the problem.
73 George
W2GS
On 9/5/2012 2:16 PM, Tim Ellison wrote:
OK. That looks OK.
I have it working here fine. Even with two instances of CWSkimmer
running on my FLEX-5000+RX2.
If you could send me a screen shot of the VAC control panel when
PowerSDR and CWS are running, that might tell me something
Tim Ellison
On 9/5/2012 3:12 PM, George wrote:
Hi Tim,
Settings are:
Cables 4
SR 8000 ... 192000
BPS 8 ... 16
NC 1 ... 2
Maxinst 20
MS per int 7
Stream: cable range
Connected source Line
Clock Corr % 100.00
The above worked with previous version I didn't change any VAC
settings when I upgraded. Thanks for your great support.
73
George
W2GS
On 9/5/2012 2:01 PM, Tim Ellison wrote:
What are the settings of your VAC cables?
Tim Ellison
On 9/5/2012 2:53 PM, George wrote:
Bernie and others,
I am seeing something similar. I see no noise in the CW skimmer
waterfall. I use the cat data from DDUtil which is being displayed
in the frequency box. Also I checked the operation of the VAC
channels using WW in both PKS31 and RTTY and that worked FB. I
have checked my settings and I don't see any thing that has changed
in VAC, Skimmer or PSDR. It looks like the I/Q data is not getting
to Skimmer. Like Bernie said "any suggestions". Thanks.
73
George
W2GS
On 9/5/2012 1:03 PM, Bernie Huth wrote:
I am not able to get CW Skimmer v 1.71 to decode properly with
PowerSDR
v2.4.4 and a Flex-3000.
The radio CAT commands seem to be working correctly using PowerSDR
v2.4.4
and DXLabs Commander. CW Skimmer is setup as a secondary CAT
control in
Commander using Kenwood CAT protocol. The correct frequency is
indicated in
both Commander and CW Skimmer.
There is noise indicated in the CW-Skimmer waterfall, however,
there is no
CW decoding indicated. The Audio setup in CW Skimmer is:
SoundCard Driver: WDM
Signal I/O Device: 04 Virtual Cable 2
Audio I/O Device: 03 Virtual Cable 1
Channels: Left/Right: I/Q
Shift Right Channel Data: 0 Samples
The Radio setup in CW Skimmer is:
Hardware Type: SoftRock IF
CW Pitch: 750 Hz
Audio IF: 9750 Hz
Sample Rate: 96 kHz
The PowerSDR v2.4.4 VAC setup is:
Primary:
Buffer Size: 1024
Sample Rate: 96000
VAC1:
Enable VAC1... Checked
Driver: Windows WDM-KS
Input: Virtual Cable 1
Output: Virtual Cable 2
Buffer Size: 1024
Sample Rate: 96000 Hz
Mono/Stereo: unchecked
Direct I/Q: checked
Calibrate I/Q: checked
Buffer Latency: 120
Allow PTT to override... checked
Any ideas?
-73-
Bernie
W4BGH
Riverview, FL
_______________________________________________
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/ Homepage:
http://www.flexradio.com/
_______________________________________________
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/ Homepage:
http://www.flexradio.com/
_______________________________________________
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/ Homepage:
http://www.flexradio.com/
_______________________________________________
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/