I have a Promise FastTrak SATA150 controller with two 120 GB drives
that are mirrored.  Using 5.1-RELEASE-p10 with sources from Nov 3.

I tried to upgrade from 5.1 to 5.2-RC today and the new kernel couldn't
mount my root partition (/dev/ar0s1a) after doing make installkernel
and rebooting into single user mode.  Browsing through the console
messages shows the individual drives (/dev/ad4 and /dev/ad6), but no
/dev/ar0.  The /dev/ar0 device shows up on the 5.1 kernel.  What did I
do wrong?  I'm using the same kernel config file (except for chaning
"options apicio" to "device apic") and followed the usual procedure
of make buildworld, make buildkernel, make installkernel reboot to
single user mode, etc.

The 5.1 kernel was CVSed on 3 Nov in the RELENG_5_1 tag and the 5.2-RC
was from RELENG_5_2 CVSed 24 Dec.

Included is my dmesg output from the 5.1 kernel and my kernel config
file SAMSON for the 5.1 kernel.  Any help would be appreciated.

Thanks,
Kevin

----------------------------------------

Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.1-RELEASE-p10 #1: Mon Nov  3 08:30:08 EST 2003
    [EMAIL PROTECTED]:/usr/obj/usr/src/sys/SAMSON
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0421000.
Preloaded elf module "/boot/kernel/miibus.ko" at 0xc0421294.
Preloaded elf module "/boot/kernel/if_fxp.ko" at 0xc0421340.
Preloaded elf module "/boot/kernel/usb.ko" at 0xc04213ec.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0421494.
Timecounter "i8254"  frequency 1193182 Hz
Timecounter "TSC"  frequency 2793015888 Hz
CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz (2793.02-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf29  Stepping = 9
  
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Hyperthreading: 2 logical CPUs
real memory  = 1073168384 (1023 MB)
avail memory = 1038090240 (990 MB)
Changing APIC ID for IO APIC #0 from 0 to 2 on chip
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): apic id:  0, version: 0x00050014, at 0xfee00000
 cpu1 (AP):  apic id:  1, version: 0x00050014, at 0xfee00000
 io0 (APIC): apic id:  2, version: 0x00178020, at 0xfec00000
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <DELL   8300   > on motherboard
pcibios: BIOS version 2.10
Using $PIR table, 8 entries at 0xc00feae0
acpi0: power button is handled as a fixed feature programming model.
Timecounter "ACPI-fast"  frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_cpu1: <CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
IOAPIC #0 intpin 16 -> irq 2
IOAPIC #0 intpin 19 -> irq 13
IOAPIC #0 intpin 18 -> irq 16
IOAPIC #0 intpin 23 -> irq 17
IOAPIC #0 intpin 17 -> irq 18
agp0: <Intel Generic host to PCI bridge> mem 0xe8000000-0xefffffff at device 0.0 on 
pci0
pcib1: <PCIBIOS PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0xff80-0xff9f irq 2 at device 
29.0 on pci0
usb0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0xff60-0xff7f irq 13 at device 
29.1 on pci0
usb1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0xff40-0xff5f irq 16 at device 
29.2 on pci0
usb2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0xff20-0xff3f irq 2 at device 
29.3 on pci0
usb3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xffa80800-0xffa80bff irq 17 at device 
29.7 on pci0
ehci_pci_attach: companion usb0
ehci_pci_attach: companion usb1
ehci_pci_attach: companion usb2
ehci_pci_attach: companion usb3
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <EHCI (generic) USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: (0x8086) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
IOAPIC #0 intpin 21 -> irq 19
IOAPIC #0 intpin 22 -> irq 20
IOAPIC #0 intpin 20 -> irq 21
atapci0: <Promise PDC20371 SATA150 controller> port 
0xdf00-0xdf7f,0xde60-0xde6f,0xde80-0xdebf mem 
0xfcee0000-0xfcefffff,0xfcecd000-0xfcecdfff irq 19 at device 0.0 on pci2
ata2: at 0xfcecd000 on atapci0
ata3: at 0xfcecd000 on atapci0
ata4: at 0xfcecd000 on atapci0
pci2: <simple comms> at device 1.0 (no driver attached)
pci2: <network, ethernet> at device 2.0 (no driver attached)
fxp0: <Intel 82801BA (D865) Pro/100 VE Ethernet> port 0xdec0-0xdeff mem 
0xfcecf000-0xfcecffff irq 21 at device 8.0 on pci2
fxp0: Ethernet address 00:07:e9:5e:28:44
miibus0: <MII bus> on fxp0
inphy0: <i82562ET 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <Intel ICH5 UDMA100 controller> port 
0xffa0-0xffaf,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 mem 
0xfebffc00-0xfebfffff irq 9 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci1
ata1: at 0x170 irq 15 on atapci1
atapci2: <Intel ICH5 SATA150 controller> port 
0xfea0-0xfeaf,0xfe30-0xfe33,0xfe20-0xfe27,0xfe10-0xfe13,0xfe00-0xfe07 irq 9 at device 
31.2 on pci0
ata5: at 0xfe00 on atapci2
ata6: at 0xfe20 on atapci2
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pci0: <multimedia, audio> at device 31.5 (no driver attached)
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 
irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
ppc0 port 0x778-0x77f,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
pmtimer0 on isa0
orm0: <Option ROMs> at iomem 
0xdd000-0xdffff,0xdb800-0xdcfff,0xda000-0xdb7ff,0xc0000-0xcf7ff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
Timecounters tick every 10.000 msec
ad4: 114473MB <ST3120023AS> [232581/16/63] at ata2-master UDMA133
ad6: 114473MB <ST3120023AS> [232581/16/63] at ata3-master UDMA133
acd0: CDROM <Lite-On LTN486S 48x Max> at ata1-master PIO4
acd1: CD-RW <HL-DT-ST GCE-8481B> at ata1-slave PIO4
ar0: 114440MB <ATA RAID1 array> [14589/255/63] status: READY subdisks:
 disk0 READY on ad4 at ata2-master
 disk1 READY on ad6 at ata3-master
SMP: AP CPU #1 Launched!
Opened disk ad4 -> 1
Opened disk ad6 -> 1
Opened disk ad6 -> 1
Mounting root from ufs:/dev/ar0s1a

----------------------------------------

#
# GENERIC -- Generic kernel configuration file for FreeBSD/i386
#
# For more information on this file, please read the handbook section on
# Kernel Configuration Files:
#
#    http://www.FreeBSD.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig-config.html
#
# The handbook is also available locally in /usr/share/doc/handbook
# if you've installed the doc distribution, otherwise always see the
# FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the
# latest information.
#
# An exhaustive list of options and more detailed explanations of the
# device lines is also present in the ../../conf/NOTES and NOTES files. 
# If you are in doubt as to the purpose or necessity of a line, check first 
# in NOTES.
#
# $FreeBSD: src/sys/i386/conf/GENERIC,v 1.384.2.2 2003/05/31 15:18:41 scottl Exp $

machine         i386
#cpu            I486_CPU
#cpu            I586_CPU
cpu             I686_CPU
ident           SAMSON

#To statically compile in device wiring instead of /boot/device.hints
#hints          "GENERIC.hints"         #Default places to look for devices.

#makeoptions    DEBUG=-g                #Build kernel with gdb(1) debug symbols

options         SCHED_4BSD              #4BSD scheduler
options         INET                    #InterNETworking
#options        INET6                   #IPv6 communications protocols
options         FFS                     #Berkeley Fast Filesystem
options         SOFTUPDATES             #Enable FFS soft updates support
#options        UFS_ACL                 #Support for access control lists
options         UFS_DIRHASH             #Improve performance on big directories
#options        MD_ROOT                 #MD is a potential root device
#options        NFSCLIENT               #Network Filesystem Client
#options        NFSSERVER               #Network Filesystem Server
#options        NFS_ROOT                #NFS usable as root device, requires NFSCLIENT
#options        MSDOSFS                 #MSDOS Filesystem
#options        CD9660                  #ISO 9660 Filesystem
#options        PROCFS                  #Process filesystem (requires PSEUDOFS)
options         PSEUDOFS                #Pseudo-filesystem framework
options         COMPAT_43               #Compatible with BSD 4.3 [KEEP THIS!]
options         COMPAT_FREEBSD4         #Compatible with FreeBSD4
#options        SCSI_DELAY=15000        #Delay (in ms) before probing SCSI
#options        KTRACE                  #ktrace(1) support
options         SYSVSHM                 #SYSV-style shared memory
options         SYSVMSG                 #SYSV-style message queues
options         SYSVSEM                 #SYSV-style semaphores
#options        _KPOSIX_PRIORITY_SCHEDULING #Posix P1003_1B real-time extensions
#options        KBD_INSTALL_CDEV        # install a CDEV entry in /dev
#options        AHC_REG_PRETTY_PRINT    # Print register bitfields in debug
                                        # output.  Adds ~128k to driver.
#options        AHD_REG_PRETTY_PRINT    # Print register bitfields in debug
                                        # output.  Adds ~215k to driver.

# Debugging for use in -current
#options        DDB                     #Enable the kernel debugger
#options        INVARIANTS              #Enable calls of extra sanity checking
#options        INVARIANT_SUPPORT       #Extra sanity checks of internal structures, 
required by INVARIANTS
#options        WITNESS                 #Enable checks to detect deadlocks and cycles
#options        WITNESS_SKIPSPIN        #Don't run witness on spinlocks for speed

# To make an SMP kernel, the next two are needed
options         SMP                     # Symmetric MultiProcessor Kernel
options         APIC_IO                 # Symmetric (APIC) I/O

device          isa
#device         eisa
device          pci

# Floppy drives
device          fdc

# ATA and ATAPI devices
device          ata
device          atadisk                 # ATA disk drives
device          atapicd                 # ATAPI CDROM drives
#device         atapifd                 # ATAPI floppy drives
#device         atapist                 # ATAPI tape drives
options         ATA_STATIC_ID           #Static device numbering

# SCSI Controllers
#device         ahb             # EISA AHA1742 family
#device         ahc             # AHA2940 and onboard AIC7xxx devices
#device         ahd             # AHA39320/29320 and onboard AIC79xx devices
#device         amd             # AMD 53C974 (Tekram DC-390(T))
#device         isp             # Qlogic family
#device         mpt             # LSI-Logic MPT-Fusion
##device                ncr             # NCR/Symbios Logic
#device         sym             # NCR/Symbios Logic (newer chipsets + those of `ncr')
#device         trm             # Tekram DC395U/UW/F DC315U adapters

#device         adv             # Advansys SCSI adapters
#device         adw             # Advansys wide SCSI adapters
#device         aha             # Adaptec 154x SCSI adapters
#device         aic             # Adaptec 15[012]x SCSI adapters, AIC-6[23]60.
#device         bt              # Buslogic/Mylex MultiMaster SCSI adapters

#device         ncv             # NCR 53C500
#device         nsp             # Workbit Ninja SCSI-3
#device         stg             # TMC 18C30/18C50

# RAID controllers interfaced to the SCSI subsystem
#device         asr             # DPT SmartRAID V, VI and Adaptec SCSI RAID
#device         ciss            # Compaq Smart RAID 5*
#device         dpt             # DPT Smartcache III, IV - See NOTES for options!
#device         iir             # Intel Integrated RAID
#device         mly             # Mylex AcceleRAID/eXtremeRAID

# SCSI peripherals
#device         scbus           # SCSI bus (required)
#device         ch              # SCSI media changers
#device         da              # Direct Access (disks)
#device         sa              # Sequential Access (tape etc)
#device         cd              # CD
#device         pass            # Passthrough device (direct SCSI access)
#device         ses             # SCSI Environmental Services (and SAF-TE)

# RAID controllers
#device         aac             # Adaptec FSA RAID
#device         aacp            # SCSI passthrough for aac (requires CAM)
#device         amr             # AMI MegaRAID
#device         ida             # Compaq Smart RAID
#device         ips             # IBM (Adaptec) ServeRAID
#device         mlx             # Mylex DAC960 family
#device         pst             # Promise Supertrak SX6000
#device         twe             # 3ware ATA RAID

# atkbdc0 controls both the keyboard and the PS/2 mouse
device          atkbdc          # AT keyboard controller
device          atkbd           # AT keyboard
device          psm             # PS/2 mouse

device          vga             # VGA video card driver

#device         splash          # Splash screen and screen saver support

# syscons is the default console driver, resembling an SCO console
device          sc

# Enable this for the pcvt (VT220 compatible) console driver
#device         vt
#options        XSERVER                 # support for X server on a vt console
#options        FAT_CURSOR              # start with block cursor

device          agp             # support several AGP chipsets

# Floating point support - do not disable.
device          npx

# Power management support (see NOTES for more options)
device          apm
# Add suspend/resume support for the i8254.
device          pmtimer

# PCCARD (PCMCIA) support
# Pcmcia and cardbus bridge support
#device         cbb                     # cardbus (yenta) bridge
#device         pcic                    # ExCA ISA and PCI bridges
#device         pccard                  # PC Card (16-bit) bus
#device         cardbus                 # CardBus (32-bit) bus

# Serial (COM) ports
device          sio             # 8250, 16[45]50 based serial ports

# Parallel port
device          ppc
device          ppbus           # Parallel port bus (required)
#device         lpt             # Printer
#device         plip            # TCP/IP over parallel
#device         ppi             # Parallel port interface device
#device         vpo             # Requires scbus and da


# PCI Ethernet NICs.
#device         de              # DEC/Intel DC21x4x (``Tulip'')
#device         em              # Intel PRO/1000 adapter Gigabit Ethernet Card
#device         txp             # 3Com 3cR990 (``Typhoon'')
#device         vx              # 3Com 3c590, 3c595 (``Vortex'')

# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
#device         miibus          # MII bus support
#device         dc              # DEC/Intel 21143 and various workalikes
#device         fxp             # Intel EtherExpress PRO/100B (82557, 82558)
#device         pcn             # AMD Am79C97x PCI 10/100 (precedence over 'lnc')
#device         rl              # RealTek 8129/8139
#device         sf              # Adaptec AIC-6915 (``Starfire'')
#device         sis             # Silicon Integrated Systems SiS 900/SiS 7016
#device         sk              # SysKonnect SK-984x and SK-982x gigabit ethernet
#device         ste             # Sundance ST201 (D-Link DFE-550TX)
#device         ti              # Alteon Networks Tigon I/II gigabit ethernet
#device         tl              # Texas Instruments ThunderLAN
#device         tx              # SMC EtherPower II (83c170 ``EPIC'')
#device         vr              # VIA Rhine, Rhine II
#device         wb              # Winbond W89C840F
#device         xl              # 3Com 3c90x (``Boomerang'', ``Cyclone'')
#device         bge             # Broadcom BCM570xx Gigabit Ethernet

# ISA Ethernet NICs.  pccard nics included.
#device         cs              # Crystal Semiconductor CS89x0 NIC
# 'device ed' requires 'device miibus'
#device         ed              # NE[12]000, SMC Ultra, 3c503, DS8390 cards
#device         ex              # Intel EtherExpress Pro/10 and Pro/10+
#device         ep              # Etherlink III based cards
#device         fe              # Fujitsu MB8696x based cards
#device         ie              # EtherExpress 8/16, 3C507, StarLAN 10 etc.
#device         lnc             # NE2100, NE32-VL Lance Ethernet cards
#device         sn              # SMC's 9000 series of ethernet chips
#device         xe              # Xircom pccard ethernet

# ISA devices that use the old ISA shims
#device         le

# Wireless NIC cards
#device         wlan            # 802.11 support
#device         an              # Aironet 4500/4800 802.11 wireless NICs. 
#device         awi             # BayStack 660 and others
#device         wi              # WaveLAN/Intersil/Symbol 802.11 wireless NICs.
#device         wl              # Older non 802.11 Wavelan wireless NIC.

# Pseudo devices - the number indicates how many units to allocate.
device          random          # Entropy device
device          loop            # Network loopback
device          ether           # Ethernet support
#device         sl              # Kernel SLIP
#device         ppp             # Kernel PPP
#device         tun             # Packet tunnel.
device          pty             # Pseudo-ttys (telnet etc)
#device         md              # Memory "disks"
#device         gif             # IPv6 and IPv4 tunneling
#device         faith           # IPv6-to-IPv4 relaying (translation)

# The `bpf' device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
device          bpf             # Berkeley packet filter

# USB support
#device         uhci            # UHCI PCI->USB interface
#device         ohci            # OHCI PCI->USB interface
#device         usb             # USB Bus (required)
#device         udbp            # USB Double Bulk Pipe devices
#device         ugen            # Generic
#device         uhid            # "Human Interface Devices"
#device         ukbd            # Keyboard
#device         ulpt            # Printer
#device         umass           # Disks/Mass storage - Requires scbus and da
#device         ums             # Mouse
#device         urio            # Diamond Rio 500 MP3 player
#device         uscanner        # Scanners
# USB Ethernet, requires mii
#device         aue             # ADMtek USB ethernet
#device         axe             # ASIX Electronics USB ethernet
#device         cue             # CATC USB ethernet
#device         kue             # Kawasaki LSI USB ethernet

# FireWire support
#device         firewire        # FireWire bus code
#device         sbp             # SCSI over FireWire (Requires scbus and da)
#device         fwe             # Ethernet over FireWire (non-standard!)
_______________________________________________
[EMAIL PROTECTED] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-hackers
To unsubscribe, send any mail to "[EMAIL PROTECTED]"

Reply via email to