> On Sun, 26 Dec 2004 13:28, [EMAIL PROTECTED] wrote: >> > Try acpiconf -i 1 >> >> Same result :/ > > Hmm.. what's your dmesg output when you boot verbose with ACPI enabled? >
Check the end of mail >> > I prefer acpi_pcc http://www.spa.is.uec.ac.jp/~nfukuda/software/ which >> I >> > believe does the same thing but only needs a kernel module to work. >> >> Does it work on Pentium-M ? > > Yep. > I'll try it out; meanwhile, I've discovered the sysctl to change this manually. I've checked it works by trying to compile something at the lowest CPU clock speed. It was slow to hell :-) >> >> load, and maxing it (1.6GHz) under load, but with ACPI off. With ACPI >> on >> >> it's always at 1.6GHz. Plus, I've noticed the 'top' CPU values are >> plain >> >> wrong. I was compiling thunderbird, xmms, and firefox and it showed >> all >> >> processes with 0.00% CPU. >> > >> > Do your kernel and userland match? >> >> 5.3-RELEASE from cd and a custom kernel I built. I've just tested, and >> the >> results are widly innacurate ONLY with ACPI turned on.. weird. > > Any chance there is a new BIOS available for that system? > A quick googling session brought up nothing. >> Did you have to do anything in special to make -i 0 work? (it says >> device >> not configured to me.. perhaps I missed something) > > No.. If I try and look at a non existent battery slot it says 'device not > configured' so maybe it thinks you have no batteries for some strange > reason. > I've installed klaptop and it shows battery as -1 and 'not charging' acpiconf -i[0-9] didn't do any good either :/ > -- > Daniel O'Connor software and network engineer > for Genesis Software - http://www.gsoft.com.au > "The nice thing about standards is that there > are so many of them to choose from." > -- Andrew Tanenbaum > GPG Fingerprint - 5596 B766 97C0 0E94 4347 295E E593 DC20 7B3F CE8C > dmesg (ACPI on, boot verbose) Copyright (c) 1992-2004 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.3-RELEASE #1: Sat Dec 25 03:41:40 WET 2004 [EMAIL PROTECTED]:/usr/src/sys/i386/compile/laptop-kernel WARNING: debug.mpsafenet forced to 0 as ipsec requires Giant WARNING: MPSAFE network stack disabled, expect reduced performance. Preloaded elf kernel "/boot/kernel/kernel" at 0xc09cb000. Calibrating clock(s) ... i8254 clock: 1193164 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 1598650059 Hz CPU: Intel(R) Pentium(R) M processor 1.60GHz (1598.65-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x6d6 Stepping = 6 Features=0xafe9f9bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,PBE> real memory = 535691264 (510 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages) 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages) 0x0000000000c26000 - 0x000000001f5b4fff, 513339392 bytes (125327 pages) avail memory = 514539520 (490 MB) bios32: Found BIOS32 Service Directory header at 0xc00f6310 bios32: Entry = 0xfd520 (c00fd520) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xfd520+0x262 pnpbios: Found PnP BIOS data at 0xc00f6350 pnpbios: Entry = f0000:ab76 Rev = 1.0 Other BIOS signatures found: wlan: <802.11 Link Layer> null: <null device, zero device> random: <entropy source, Software, Yarrow> io: <I/O> mem: <memory> Pentium Pro MTRR support enabled acpi0: <ACER Kestrel> on motherboard acpi0: [MPSAFE] pci_open(1): mode 1 addr port (0x0cf8) is 0x8000f904 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=35808086) pcibios: BIOS version 2.10 Found $PIR table, 9 entries at 0xc00fdd00 PCI-Only Interrupts: none Location Bus Device Pin Link IRQs embedded 0 30 A 0x60 6 embedded 0 30 B 0x61 10 embedded 0 30 C 0x62 6 embedded 0 30 D 0x63 6 embedded 2 6 A 0x68 10 embedded 2 6 B 0x69 10 embedded 2 6 C 0x6a 6 embedded 2 4 A 0x61 10 embedded 2 4 B 0x62 6 embedded 2 2 A 0x63 6 embedded 0 0 A 0x60 6 embedded 0 0 B 0x61 10 embedded 0 0 C 0x62 6 embedded 0 0 D 0x63 6 embedded 0 31 A 0x62 6 embedded 0 31 B 0x61 10 embedded 0 29 A 0x60 6 embedded 0 29 B 0x63 6 embedded 0 29 C 0x62 6 embedded 0 29 D 0x6b 10 embedded 0 1 A 0x60 6 embedded 0 1 B 0x61 10 slot 1 1 0 A 0x60 6 slot 1 1 0 B 0x61 10 AcpiOsDerivePciId: bus 0 dev 31 func 0 AcpiOsDerivePciId: bus 0 dev 31 func 0 AcpiOsDerivePciId: bus 0 dev 31 func 1 acpi0: Power Button (fixed) atpic: Programming IRQ9 as level/low AcpiOsDerivePciId: bus 0 dev 0 func 0 AcpiOsDerivePciId: bus 0 dev 0 func 1 acpi_ec0: <Embedded Controller: GPE 0x1d> port 0x66,0x62 on acpi0 acpi_ec0: info: new max delay is 970 us ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 ACPI timer looks GOOD min = 2, max = 3, width = 1 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 cpu0: <ACPI CPU (3 Cx states)> on acpi0 acpi_tz0: <Thermal Zone> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 ACPI PCI link initial configuration: \\_SB_.PCI0.LPC0.LNKA irq 0: [ 6] 6+ low,level,sharable 0.1.0 \\_SB_.PCI0.LPC0.LNKA irq 0: [ 6] 6+ low,level,sharable 0.29.0 \\_SB_.PCI0.LPC0.LNKD irq 0: [ 6] 6+ low,level,sharable 0.29.1 \\_SB_.PCI0.LPC0.LNKC irq 0: [ 6] 6+ low,level,sharable 0.29.2 \\_SB_.PCI0.LPC0.LNKH irq 0: [10] 10+ low,level,sharable 0.29.3 \\_SB_.PCI0.LPC0.LNKC irq 0: [ 6] 6+ low,level,sharable 0.31.0 \\_SB_.PCI0.LPC0.LNKB irq 0: [10] 10+ low,level,sharable 0.31.1 pci0: <ACPI PCI bus> on pcib0 pci0: physical bus=0 map[10]: type 3, range 32, base e0000000, size 28, enabled found-> vendor=0x8086, dev=0x3580, revid=0x02 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0106, statreg=0x3090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x3584, revid=0x02 bus=0, slot=0, func=1 class=08-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0080, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x3585, revid=0x02 bus=0, slot=0, func=3 class=08-80-00, hdrtype=0x00, mfdev=1 cmdreg=0x0006, statreg=0x0080, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x3581, revid=0x02 bus=0, slot=1, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x00a0, cachelnsz=0 (dwords) lattimer=0x60 (2880 ns), mingnt=0x0c (3000 ns), maxlat=0x00 (0 ns) map[20]: type 4, range 32, base 00001800, size 5, enabled pcib0: matched entry for 0.29.INTA (src \\_SB_.PCI0.LPC0.LNKA) pcib0: possible interrupts: 6 ACPI PCI link arbitrated settings: \\_SB_.PCI0.LPC0.LNKA (references 2, priority 10100): interrupts: 6 penalty: 5050 \\_SB_.PCI0.LPC0.LNKC (references 2, priority 10100): interrupts: 6 penalty: 5050 \\_SB_.PCI0.LPC0.LNKD (references 1, priority 5050): interrupts: 6 penalty: 5050 \\_SB_.PCI0.LPC0.LNKH (references 1, priority 20): interrupts: 10 penalty: 20 \\_SB_.PCI0.LPC0.LNKB (references 1, priority 20): interrupts: 10 penalty: 20 pcib0: slot 29 INTA routed to irq 6 via \\_SB_.PCI0.LPC0.LNKA found-> vendor=0x8086, dev=0x24c2, revid=0x03 bus=0, slot=29, func=0 class=0c-03-00, hdrtype=0x00, mfdev=1 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=6 map[20]: type 4, range 32, base 00001820, size 5, enabled pcib0: matched entry for 0.29.INTB (src \\_SB_.PCI0.LPC0.LNKD) pcib0: possible interrupts: 6 ACPI PCI link arbitrated settings: \\_SB_.PCI0.LPC0.LNKC (references 2, priority 10240): interrupts: 6 penalty: 5120 \\_SB_.PCI0.LPC0.LNKD (references 1, priority 5120): interrupts: 6 penalty: 5120 \\_SB_.PCI0.LPC0.LNKH (references 1, priority 40): interrupts: 10 penalty: 40 \\_SB_.PCI0.LPC0.LNKB (references 1, priority 40): interrupts: 10 penalty: 40 pcib0: slot 29 INTB routed to irq 6 via \\_SB_.PCI0.LPC0.LNKD found-> vendor=0x8086, dev=0x24c4, revid=0x03 bus=0, slot=29, func=1 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=6 map[20]: type 4, range 32, base 00001840, size 5, enabled pcib0: matched entry for 0.29.INTC (src \\_SB_.PCI0.LPC0.LNKC) pcib0: possible interrupts: 6 ACPI PCI link arbitrated settings: \\_SB_.PCI0.LPC0.LNKC (references 2, priority 10360): interrupts: 6 penalty: 5180 \\_SB_.PCI0.LPC0.LNKH (references 1, priority 60): interrupts: 10 penalty: 60 \\_SB_.PCI0.LPC0.LNKB (references 1, priority 60): interrupts: 10 penalty: 60 pcib0: slot 29 INTC routed to irq 6 via \\_SB_.PCI0.LPC0.LNKC found-> vendor=0x8086, dev=0x24c7, revid=0x03 bus=0, slot=29, func=2 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=c, irq=6 map[10]: type 1, range 32, base d0000000, size 10, enabled pcib0: matched entry for 0.29.INTD (src \\_SB_.PCI0.LPC0.LNKH) pcib0: possible interrupts: 10 ACPI PCI link arbitrated settings: \\_SB_.PCI0.LPC0.LNKH (references 1, priority 80): interrupts: 10 penalty: 80 \\_SB_.PCI0.LPC0.LNKB (references 1, priority 80): interrupts: 10 penalty: 80 pcib0: slot 29 INTD routed to irq 10 via \\_SB_.PCI0.LPC0.LNKH found-> vendor=0x8086, dev=0x24cd, revid=0x03 bus=0, slot=29, func=7 class=0c-03-20, hdrtype=0x00, mfdev=0 cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=d, irq=10 powerspec 2 supports D0 D3 current D0 found-> vendor=0x8086, dev=0x2448, revid=0x83 bus=0, slot=30, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x8880, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x24cc, revid=0x03 bus=0, slot=31, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[20]: type 4, range 32, base 00001860, size 4, enabled found-> vendor=0x8086, dev=0x24ca, revid=0x03 bus=0, slot=31, func=1 class=01-01-8a, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 map[20]: type 4, range 32, base 00001880, size 5, enabled pcib0: matched entry for 0.31.INTB (src \\_SB_.PCI0.LPC0.LNKB) pcib0: possible interrupts: 10 ACPI PCI link arbitrated settings: \\_SB_.PCI0.LPC0.LNKB (references 1, priority 110): interrupts: 10 penalty: 110 pcib0: slot 31 INTB routed to irq 10 via \\_SB_.PCI0.LPC0.LNKB found-> vendor=0x8086, dev=0x24c3, revid=0x03 bus=0, slot=31, func=3 class=0c-05-00, hdrtype=0x00, mfdev=0 cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=10 map[10]: type 4, range 32, base 00001c00, size 8, enabled map[14]: type 4, range 32, base 000018c0, size 6, enabled map[18]: type 1, range 32, base d0000c00, size 9, enabled map[1c]: type 1, range 32, base d0000800, size 8, enabled pcib0: matched entry for 0.31.INTB (src \\_SB_.PCI0.LPC0.LNKB) pcib0: slot 31 INTB is already routed to irq 10 found-> vendor=0x8086, dev=0x24c5, revid=0x03 bus=0, slot=31, func=5 class=04-01-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=10 powerspec 2 supports D0 D3 current D0 map[10]: type 4, range 32, base 00002400, size 8, enabled map[14]: type 4, range 32, base 00002000, size 7, enabled pcib0: matched entry for 0.31.INTB (src \\_SB_.PCI0.LPC0.LNKB) pcib0: slot 31 INTB is already routed to irq 10 found-> vendor=0x8086, dev=0x24c6, revid=0x03 bus=0, slot=31, func=6 class=07-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=10 powerspec 2 supports D0 D3 current D0 agp0: <Intel Generic host to PCI bridge> mem 0xe0000000-0xefffffff at device 0.0 on pci0 agp0: Reserved 0x10000000 bytes for rid 0x10 type 3 at 0xe0000000 agp0: allocating GATT for aperture of size 196M pci0: <base peripheral> at device 0.1 (no driver attached) pci0: <base peripheral> at device 0.3 (no driver attached) pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pcib1: secondary bus 1 pcib1: subordinate bus 1 pcib1: I/O decode 0x3000-0x3fff pcib1: memory decode 0xd0100000-0xd01fffff pcib1: prefetched decode 0xd8000000-0xdfffffff ACPI PCI link initial configuration: \\_SB_.PCI0.LPC0.LNKA irq* 6: [ 6] 6+ low,level,sharable 1.0.0 pci1: <ACPI PCI bus> on pcib1 pci1: physical bus=1 map[10]: type 3, range 32, base d8000000, size 27, enabled pcib1: device (null) requested decoded memory range 0xd8000000-0xdfffffff map[14]: type 4, range 32, base 00003000, size 8, enabled pcib1: device (null) requested decoded I/O range 0x3000-0x30ff map[18]: type 1, range 32, base d0100000, size 16, enabled pcib1: device (null) requested decoded memory range 0xd0100000-0xd010ffff pcib1: matched entry for 1.0.INTA (src \\_SB_.PCI0.LPC0.LNKA) pcib1: slot 0 INTA is already routed to irq 6 found-> vendor=0x1002, dev=0x4e50, revid=0x00 bus=1, slot=0, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0307, statreg=0x02b0, cachelnsz=8 (dwords) lattimer=0x42 (1980 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns) intpin=a, irq=6 powerspec 2 supports D0 D1 D2 D3 current D0 pci1: <display, VGA> at device 0.0 (no driver attached) uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0x1800-0x181f irq 6 at device 29.0 on pci0 uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1800 uhci0: [GIANT-LOCKED] usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0x1820-0x183f irq 6 at device 29.1 on pci0 uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1820 uhci1: [GIANT-LOCKED] usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0x1840-0x185f irq 6 at device 29.2 on pci0 uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1840 uhci2: [GIANT-LOCKED] usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2 usb2: USB revision 1.0 uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered pci0: <serial bus, USB> at device 29.7 (no driver attached) pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pcib2: secondary bus 2 pcib2: subordinate bus 2 pcib2: I/O decode 0x4000-0x4fff pcib2: memory decode 0xd0200000-0xd05fffff pcib2: prefetched decode 0xfff00000-0xfffff pcib2: Subtractively decoded bridge. ACPI PCI link initial configuration: \\_SB_.PCI0.LPC0.LNKD irq* 6: [ 6] 6+ low,level,sharable 2.2.0 \\_SB_.PCI0.LPC0.LNKB irq*10: [10] 10+ low,level,sharable 2.4.0 \\_SB_.PCI0.LPC0.LNKC irq* 6: [ 6] 6+ low,level,sharable 2.4.1 \\_SB_.PCI0.LPC0.LNKE irq 0: [10] 10+ low,level,sharable 2.6.0 \\_SB_.PCI0.LPC0.LNKF irq 0: [10] 0+ low,level,sharable 2.6.1 \\_SB_.PCI0.LPC0.LNKG irq 0: [ 6] 0+ low,level,sharable 2.6.2 pci2: <ACPI PCI bus> on pcib2 pci2: physical bus=2 map[10]: type 1, range 32, base d0204000, size 13, enabled pcib2: device (null) requested decoded memory range 0xd0204000-0xd0205fff pcib2: matched entry for 2.2.INTA (src \\_SB_.PCI0.LPC0.LNKD) pcib2: slot 2 INTA is already routed to irq 6 found-> vendor=0x14e4, dev=0x4401, revid=0x01 bus=2, slot=2, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0106, statreg=0x0810, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=6 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base d0208000, size 12, enabled pcib2: device (null) requested decoded memory range 0xd0208000-0xd0208fff pcib2: matched entry for 2.4.INTA (src \\_SB_.PCI0.LPC0.LNKB) pcib2: slot 4 INTA is already routed to irq 10 found-> vendor=0x8086, dev=0x4220, revid=0x05 bus=2, slot=4, func=0 class=02-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0116, statreg=0x0290, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0x03 (750 ns), maxlat=0x18 (6000 ns) intpin=a, irq=10 powerspec 2 supports D0 D3 current D0 map[10]: type 1, range 32, base d0209000, size 12, memory disabled pcib2: device (null) requested decoded memory range 0xd0209000-0xd0209fff pcib2: matched entry for 2.6.INTA (src \\_SB_.PCI0.LPC0.LNKE) pcib2: possible interrupts: 10 ACPI PCI link arbitrated settings: \\_SB_.PCI0.LPC0.LNKG (references 1, priority 5360): interrupts: 6 penalty: 5360 \\_SB_.PCI0.LPC0.LNKE (references 1, priority 180): interrupts: 10 penalty: 180 \\_SB_.PCI0.LPC0.LNKF (references 1, priority 180): interrupts: 10 penalty: 180 pcib2: slot 6 INTA routed to irq 10 via \\_SB_.PCI0.LPC0.LNKE found-> vendor=0x104c, dev=0x8031, revid=0x00 bus=2, slot=6, func=0 class=06-07-00, hdrtype=0x02, mfdev=1 cmdreg=0x0104, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x03 (750 ns) intpin=a, irq=10 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base d020a000, size 11, enabled pcib2: device (null) requested decoded memory range 0xd020a000-0xd020a7ff map[14]: type 1, range 32, base d0200000, size 14, enabled pcib2: device (null) requested decoded memory range 0xd0200000-0xd0203fff pcib2: matched entry for 2.6.INTA (src \\_SB_.PCI0.LPC0.LNKE) pcib2: slot 6 INTA is already routed to irq 10 found-> vendor=0x104c, dev=0x8032, revid=0x00 bus=2, slot=6, func=2 class=0c-00-10, hdrtype=0x00, mfdev=1 cmdreg=0x0116, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0x03 (750 ns), maxlat=0x04 (1000 ns) intpin=a, irq=10 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base d0206000, size 13, enabled pcib2: device (null) requested decoded memory range 0xd0206000-0xd0207fff pcib2: matched entry for 2.6.INTA (src \\_SB_.PCI0.LPC0.LNKE) pcib2: slot 6 INTA is already routed to irq 10 found-> vendor=0x104c, dev=0x8033, revid=0x00 bus=2, slot=6, func=3 class=01-80-00, hdrtype=0x00, mfdev=1 cmdreg=0x0106, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0x07 (1750 ns), maxlat=0x04 (1000 ns) intpin=a, irq=10 powerspec 2 supports D0 D1 D2 D3 current D0 bfe0: <Broadcom BCM4401 Fast Ethernet> mem 0xd0204000-0xd0205fff irq 6 at device 2.0 on pci2 bfe0: Reserved 0x2000 bytes for rid 0x10 type 3 at 0xd0204000 miibus0: <MII bus> on bfe0 bmtphy0: <BCM4401 10/100baseTX PHY> on miibus0 bmtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto bfe0: bpf attached bfe0: Ethernet address: 00:c0:9f:6a:8e:1c bfe0: [GIANT-LOCKED] pci2: <network> at device 4.0 (no driver attached) cbb0: <PCI-CardBus Bridge> mem 0xd0209000-0xd0209fff irq 10 at device 6.0 on pci2 cbb0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xd0209000 cardbus0: <CardBus bus> on cbb0 pccard0: <16-bit PCCard bus> on cbb0 cbb0: [MPSAFE] cbb0: PCI Configuration space: 0x00: 0x8031104c 0x02100107 0x06070000 0x00824008 0x10: 0xd0209000 0x020000a0 0x20030302 0xfffff000 0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc 0x30: 0x00000000 0xfffffffc 0x00000000 0x0740010a 0x40: 0x00641025 0x00000001 0x00000000 0x00000000 0x50: 0x00000000 0x00000000 0x00000000 0x00000000 0x60: 0x00000000 0x00000000 0x00000000 0x00000000 0x70: 0x00000000 0x00000000 0x00000000 0x00000000 0x80: 0x18441060 0x02c00019 0x000f0000 0x01a21b22 0x90: 0x606480c0 0x00000000 0x00000000 0x00000000 0xa0: 0xfe120001 0x00c00000 0x00000000 0x00000000 0xb0: 0x08000000 0x00000000 0x00000000 0x00000000 0xc0: 0x00000000 0x00000000 0x00000000 0x00000000 0xd0: 0x00000000 0x00000000 0x00000000 0x00000000 0xe0: 0x00000000 0x00000000 0x00000000 0x00000000 0xf0: 0x00000000 0x00000000 0x00000000 0x00000000 fwohci0: vendor=104c, dev=8032 fwohci0: <1394 Open Host Controller Interface> mem 0xd0200000-0xd0203fff,0xd020a000-0xd020a7ff irq 10 at device 6.2 on pci2 fwohci0: Reserved 0x800 bytes for rid 0x10 type 3 at 0xd020a000 fwohci0: [GIANT-LOCKED] fwohci0: OHCI version 1.10 (ROM=1) fwohci0: No. of Isochronous channels is 4. fwohci0: EUI64 00:c0:9f:00:00:32:14:de fwohci0: Phy 1394a available S400, 2 ports. fwohci0: Link S400, max_rec 2048 bytes. firewire0: <IEEE1394(FireWire) bus> on fwohci0 fwe0: <Ethernet over FireWire> on firewire0 if_fwe0: Fake Ethernet address: 02:c0:9f:32:14:de fwe0: bpf attached fwe0: Ethernet address: 02:c0:9f:32:14:de sbp0: <SBP-2/SCSI over FireWire> on firewire0 fwohci0: Initiate bus reset fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) firewire0: bus manager 0 (me) pci2: <mass storage> at device 6.3 (no driver attached) isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH4 UDMA100 controller> port 0x1860-0x186f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 31.1 on pci0 atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x1860 ata0: channel #0 on atapci0 atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0 atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6 ata0: reset tp1 mask=03 ostat0=50 ostat1=00 ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata0-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00 ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER> ata0: [MPSAFE] ata1: channel #1 on atapci0 atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170 atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376 ata1: reset tp1 mask=03 ostat0=50 ostat1=00 ata1-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb ata1-slave: stat=0x00 err=0x00 lsb=0x00 msb=0x00 ata1: reset tp2 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER> ata1: [MPSAFE] pci0: <serial bus, SMBus> at device 31.3 (no driver attached) pci0: <multimedia, audio> at device 31.5 (no driver attached) pci0: <simple comms> at device 31.6 (no driver attached) acpi_lid0: <Control Method Lid Switch> on acpi0 acpi_button0: <Sleep Button> on acpi0 unknown: not probed (disabled) atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0047 atkbd: keyboard ID 0x41ab (2) kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 atkbd0: [GIANT-LOCKED] psm0: unable to allocate IRQ unknown: not probed (disabled) psmcpnp0: <PS/2 mouse port> irq 12 on acpi0 psm0: current command byte:0047 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: [GIANT-LOCKED] psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons psm0: config:00000000, flags:00000008, packet size:3 psm0: syncmask:c0, syncbits:00 unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) sio0: irq maps: 0x601 0x609 0x601 0x601 sio0 port 0x2f8-0x2ff irq 3 drq 1 flags 0x10 on acpi0 sio0: type 16550A unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it atkbdc: atkbdc0 already exists; skipping it sio: sio0 already exists; skipping it Trying Read_Port at 203 Trying Read_Port at 243 Trying Read_Port at 283 Trying Read_Port at 2c3 Trying Read_Port at 303 Trying Read_Port at 343 Trying Read_Port at 383 Trying Read_Port at 3c3 ex_isa_identify() unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff ahc_isa_probe 1: ioport 0x1c00 alloc failed sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices orm0: <ISA Option ROMs> at iomem 0xe0000-0xe3fff,0xdf800-0xdffff,0xd0000-0xd17ff,0xc0000-0xcffff on isa0 pmtimer0 on isa0 adv0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) bt0: not probed (disabled) cs0: not probed (disabled) ed0: not probed (disabled) fdc0 failed to probe at port 0x3f0-0x3f5 irq 6 drq 2 on isa0 fe0: not probed (disabled) ie0: not probed (disabled) lnc0: not probed (disabled) pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0 pcic1: not probed (disabled) ppc0: parallel port not found. ppc0: <Parallel port> failed to probe at irq 7 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) sio1 failed to probe at port 0x2f8 irq 3 on isa0 sio2: not probed (disabled) sio3: not probed (disabled) sn0: not probed (disabled) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 fb0: vga0, vga, type:VGA (5), flags:0x7007f fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k vga0: vga: WARNING: video mode switching is not fully supported on this adapter VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 67 5b 4f 4f 9f 52 16 9e 1f 00 4f 0d 0e 00 00 07 80 93 87 8f 28 1f 8f 9f a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff EGA/VGA parameters to be used for mode 24 50 18 10 00 00 00 03 00 02 67 5b 4f 4f 9f 52 16 9e 1f 00 4f 0d 0e 00 00 07 80 93 87 8f 28 1f 8f 9f a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff vt0: not probed (disabled) isa_probe_children: probing PnP devices Device configuration finished. procfs registered Timecounter "TSC" frequency 1598650059 Hz quality 800 Timecounters tick every 10.000 msec WARNING: apm_saver module requires apm enabled splash: image decoder found: apm_saver IPsec: Initialized Security Association Processing. pflog0: bpf attached lo0: bpf attached cpu0: set speed to 100.0% acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0% ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin ata0-master: setting PIO4 on Intel ICH4 chip ata0-master: setting UDMA100 on Intel ICH4 chip ad0: <TOSHIBA MK6025GAS/KA200A> ATA-6 disk at ata0-master ad0: 57231MB (117210240 sectors), 116280 C, 16 H, 63 S, 512 B ad0: 16 secs/int, 1 depth queue, UDMA100 GEOM: new disk ad0 ar: FreeBSD check1 failed ata1-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin ata1-master: setting PIO4 on Intel ICH4 chip ata1-master: setting UDMA33 on Intel ICH4 chip acd0: <Slimtype DVDRW SOSW-852S/PRS9> DVDR drive at ata1 as master acd0: read 4134KB/s (4134KB/s) write 4134KB/s (4134KB/s), 2048KB buffer, UDMA33 acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, packet acd0: Writes: CDR, CDRW, DVDR, test write, burnproof acd0: Audio: play, 256 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: no/blank disc [0] f:00 typ:18 s(CHS):0/1/1 e(CHS):382/254/63 s:63 l:6152832 [1] f:00 typ:6 s(CHS):383/0/1 e(CHS):1023/254/63 s:6152895 l:31455270 [2] f:80 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:37608165 l:79602075 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad0s1, start 32256 length 3150249984 end 3150282239 GEOM: Configure ad0s2, start 3150282240 length 16105098240 end 19255380479 GEOM: Configure ad0s3, start 19255380480 length 40756262400 end 60011642879 GEOM: Configure ad0s3a, start 0 length 134217728 end 134217727 GEOM: Configure ad0s3b, start 13220446208 length 1073741824 end 14294188031 GEOM: Configure ad0s3c, start 0 length 40756262400 end 40756262399 GEOM: Configure ad0s3d, start 134217728 length 134217728 end 268435455 GEOM: Configure ad0s3e, start 268435456 length 67108864 end 335544319 GEOM: Configure ad0s3f, start 335544320 length 12884901888 end 13220446207 GEOM: Configure ad0s3g, start 14294188032 length 26462074368 end 40756262399 acpi_ec0: info: new max delay is 11000 us (probe5:sbp0:0:5:0): error 22 (probe5:sbp0:0:5:0): Unretryable Error (probe6:sbp0:0:6:0): error 22 (probe6:sbp0:0:6:0): Unretryable Error (probe0:sbp0:0:0:0): error 22 (probe0:sbp0:0:0:0): Unretryable Error (probe1:sbp0:0:1:0): error 22 (probe1:sbp0:0:1:0): Unretryable Error (probe2:sbp0:0:2:0): error 22 (probe2:sbp0:0:2:0): Unretryable Error (probe3:sbp0:0:3:0): error 22 (probe3:sbp0:0:3:0): Unretryable Error (probe4:sbp0:0:4:0): error 22 (probe4:sbp0:0:4:0): Unretryable Error Mounting root from ufs:/dev/ad0s3a WARNING: / was not properly dismounted start_init: trying /sbin/init WARNING: /home was not properly dismounted WARNING: /tmp was not properly dismounted WARNING: /usr was not properly dismounted WARNING: /var was not properly dismounted
dmesg
Description: Binary data
dmesg
Description: Binary data
_______________________________________________ freebsd-hackers@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-hackers To unsubscribe, send any mail to "[EMAIL PROTECTED]"