The config works - just don't think it is optimal. I structured it based on the mpd5.conf.sample and some other configurations stolen from dslreports.com.
I am looking more for advised MRU/MTU, and MRRU values for the links and the bundle as a whole as I do not believe my settings are optimal. I have tested a 2link configuration with similar values and obtained very, very fast speeds. Adding the 3rd link with the settings below does improve the speed, but I do not feel it is as fast as it should be. Repsectfully, David Carrick AIX Services | Spectra Energy 519.436.4600 x2464 (desk) 800.571.8446 x2464 (toll free) 519.437.7194 (cell) -----Original Message----- From: Julian Elischer [mailto:julianelisc...@gmail.com] On Behalf Of Julian Elischer Sent: April-22-10 12:12 PM To: Carrick, David Cc: freebsd-net@freebsd.org Subject: Re: 3-Line MLPPP DSL on BSD - MTU/MRRU/MRU?? On 4/22/10 8:35 AM, Carrick, David wrote: > Hi Guys, > > I have posted this question in a few different forums but I have not > had much luck with a response and I'm hoping someone can help me > out. I recently upgraded to a triple-5meg DSL service setup with > MLPPP here in Ontario Canada through a provider called Teksavvy. I > chose FreeBSD as my o/s of choice and I'm using MPD5.5 to bond the > connections. I believe they are using Juniper equipment on their > end, not sure if > matters. > > I have been using Linux for 15 years, and am an AIX Infrastructure > Analyst by trade, but I am not very familiar with more advanced > networking terms and technologies, and I am pretty new to FreeBSD. > > I was wondering if someone could help me with the optimal values > for my mpd.conf file - Max Transmit units, Max recieve unit, all > that stuff. Here is what I've got going so far... Please note I am > not on the freebsd-net mailing list so if you could CC me on the > responses that would be great! Not my area of best knowledge but a couple of points.. Use 'load' to abstract away common items from the links Try not to reference things until after they are defined.. is this working? and if not, what happens? (keep list on Cc please) # How I would have structured it: # just off the top of my head.. untested and probably with errors. default: load DSL common: set link max-redial 0 set link keep-alive 10 60 set pppoe service "teksavvy" set link enable multilink set link enable shortseq set link disable protocomp set link mrru 1500 # set link mru 1500 set link mtu 1492 set link bandwidth 5056000 set link action bundle B1 L1: create link static L1 pppoe set auth authname x...@wiredhighspeed.com set auth password xxx set pppoe iface fxp1 load common open L2: create link static L2 pppoe set auth authname x...@wiredhighspeed.com set auth password xxx set pppoe iface fxp2 load common open L3: create link static L3 pppoe set auth authname x...@wiredhighspeed.com set auth password xxx set pppoe iface fxp3 load common open DSL: create bundle static B1 set iface route default set ipcp ranges 0.0.0.0/0 0.0.0.0/0 set ipcp enable req-pri-dns set ipcp enable req-sec-dns set ipcp disable vjcomp set bundle disable round-robin set bundle disable bw-manage set iface mtu 1492 set iface disable on-demand set iface enable tcpmssfix load L1 load L2 load L3 set bundle links L1 L2 L3 _______________________________________________ freebsd-net@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-net To unsubscribe, send any mail to "freebsd-net-unsubscr...@freebsd.org"
