Paul Schmehl wrote:
When you use FreeBSD's boot manager, you get a menu like this at bootup:
F1 DOS
F2 FreeBSD
F3 Linux
F4 ??
F5 Drive 1
Default: F2
Is there a way to edit the list? Or is that fixed when boot manager
is installed and not configurable?
You have to edit the source. If you know the hex for the partition type
then it's reasonably easy. Below is a simple patch that adds 0x7 (my
NTFS/Windows) and recognises it as DOS. Done out of curiosity, more
than anything.
(From memory...)
cd /usr/src
patch < {patchname}
cd sys/boot/i386/boot0/
make
make install
boot0cfg -B -o packet /dev/{your disk}
Be warned that the final boot0cfg has to be 512 bytes so if you add a
string it may become longer. I haven't tested my patch for the serial
console boot. The patch incorporates taking out the bell on
non-serial-console boots as well (pinched from somewhere else, now
forgotten) -- it was just annoying. The patch comes with no warranties,
but it's working for me. (I don't promise either that including it here
won't bu**er up the spaces/tabs).
Of course, once you applied and rebuilt you have to write it to your
boot sector. Man boot0cfg and don't forget -o packet if your partitions
go past cylinder 1024. And have a FreebSD boot CD handy so you can
rewrite with a standard one if this doesn't work!
The final problem is that if you use cvsup it will trash all over any
source changes you make when you next run it. Doing anything about that
seems more complicated than can be justified for a small number of
patches so I just keep them in a separate dir an re-apply them whenever
I need to. In this case, it will be just after I reaslise that I've
installed a beeping boot manager again :-)
--Alex
PS just spotted the -m flag to boo0cfg for the first time. Amazing what
you find when you read the man pages :-)
--- sys/boot/i386/boot0/boot0.S.orig Wed Jan 26 19:11:21 2005
+++ sys/boot/i386/boot0/boot0.S Thu May 26 00:51:34 2005
@@ -29,7 +29,7 @@
.set PRT_OFF,0x1be # Partition table
.set TBL0SZ,0x3 # Table 0 size
- .set TBL1SZ,0xb # Table 1 size
+ .set TBL1SZ,0xc # Table 1 size
.set MAGIC,0xaa55 # Magic: bootable
.set B0MAGIC,0xbb66 # Identification
@@ -201,9 +201,13 @@
/*
* Start of input loop. Beep and take note of time
*/
+#ifdef SIO
main.10: movb $ASCII_BEL,%al # Signal
callw putchr # beep!
xorb %ah,%ah # BIOS: Get
+#else
+main.10: xorb %ah,%ah # BIOS: Get
+#endif /* SIO */
int $0x1a # system time
movw %dx,%di # Ticks when
addw _TICKS(%bp),%di # timeout
@@ -409,7 +413,7 @@
/*
* These values indicate bootable types we know the names of.
*/
- .byte 0x1, 0x4, 0x6, 0xb, 0xc, 0xe, 0x83
+ .byte 0x1, 0x4, 0x6, 0x7, 0xb, 0xc, 0xe, 0x83
.byte 0x9f, 0xa5, 0xa6, 0xa9
/*
* These are offsets that match the known names above and point to the strings
@@ -419,6 +423,7 @@
.byte os_dos-. # DOS
.byte os_dos-. # DOS
.byte os_dos-. # DOS
+ .byte os_dos-. # Windows
.byte os_dos-. # Windows
.byte os_dos-. # Windows
.byte os_dos-. # Windows
_______________________________________________
freebsd-questions@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
