Arg! This is indeed a winmodem according to the USRobotics website. I knew to avoid those like the plague, but since the modem cost twice as much as all the other modems and it didn't say winmodem anywhere on the box I figured it was safe. I thought USR was reputable. This sucks. I feel duped. Off to the store to replace this....
Thanks, Alex ---------- Original Message ----------- From: "JJB" <[EMAIL PROTECTED]> To: "Alex Teslik" <[EMAIL PROTECTED]>, "list-freebsd-questions" <[EMAIL PROTECTED]> Sent: Sat, 7 Feb 2004 12:56:45 -0500 Subject: RE: 3Com USRobotics 5699B 56k fax modem install > On 4.8 the dmesg > pci0: <unknown card> (vendor=0x12b9, dev=0x1007) at 10.0 irq 2 > > Means one of 2 things. > > your modem is what is known as an winmodem. A cheap modem mfg just > for ms/windblows market. Which FBSD does not work with. If this PCI > modem card works under windows with special driver loaded then it's > am winmodem. You can look at the modem circuit board and if it has > lucent chips, it's an winmodem. You are SOL. Replace it with an PCI > modom card that has onboard controller and DSP functions. Or use > any external serial modem. > > Your PC has legacy bios which does not ID PCI modem cards correctly. > In this case add device pun to your kernel source and recompile > it. > This device has additional code to probe your system's bio's using > different methods which in most cases results on your PCI modem card > being found. Also works for unknown Nic cards on PC with legacy > bio's. > > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] Behalf Of Alex Teslik > Sent: Saturday, February 07, 2004 12:09 PM > To: list-freebsd-questions > Subject: 3Com USRobotics 5699B 56k fax modem install > > Hello, > > I've been trying to get this faxmodem setup so I can use > hylafax, but with > marginal luck. There is lots of documentation for adding support for > ISA PNP > modems, but I can't find anything for PCI PNP modems. I don't know > what to do > from here. > > Here is some output - any recommendations greatly appreciated: > > dmesg: > ... > pci0: <unknown card> (vendor=0x12b9, dev=0x1007) at 10.0 irq 2 > ... > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 16550A > sio1 at port 0x2f8-0x2ff irq 3 on isa0 > sio1: type 16550A > > pciconf -lv: > [EMAIL PROTECTED]:10:0: class=0x078000 card=0x00c212b9 > chip=0x100712b9 > rev=0x00 hdr=0x00 > vendor = '3COM Corp, Modem Division (Formerly US Robotics)' > device = 'ERL3263A-0 USR 56k Internal DF GWPCI PC99' > class = simple comms > > uname -a: > FreeBSD xxx.xxx.xxx 4.8-RELEASE FreeBSD 4.8-RELEASE #5: Fri Feb 6 > 07:22:37 > PST 2004 > [EMAIL PROTECTED]:/usr/obj/usr/src/sys/DUALP3-4_8_0-RELEASE i386 > > pnpinfo is not relevant with this card because this card is PCI, not > ISA. > > Thanks! > Alex > _______________________________________________ > [EMAIL PROTECTED] mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-questions > To unsubscribe, send any mail to > "[EMAIL PROTECTED]" ------- End of Original Message ------- _______________________________________________ [EMAIL PROTECTED] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-questions To unsubscribe, send any mail to "[EMAIL PROTECTED]"