On 28 Feb 2010, at 17:38, Jim Pingle wrote: > On 2/28/2010 7:54 AM, Rui Paulo wrote: >> On 28 Feb 2010, at 03:22, Jim Pingle wrote: >>> >>> Are you aware if similar work ongoing for the mwl(4) based 802.11n >>> cards? I picked up a couple cheap this past week and have them working >>> with hostapd but, as with the OP in the thread, only with G rates. >>> >>> The ifconfig[1] output suggests that it is using 40MHz wide ht channels >>> but devices only associate at 54Mbps[2]. >>> >>> Jim >>> >>> [1] ifconfig mwl0_wlan1 >>> mwl0_wlan1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 >>> mtu 1500 >>> ether 00:01:36:17:96:0e >>> inet6 fe80::201:36ff:fe17:960e%mwl0_wlan1 prefixlen 64 scopeid 0x9 >>> inet 192.168.15.1 netmask 0xffffff00 broadcast 192.168.15.255 >>> nd6 options=3<PERFORMNUD,ACCEPT_RTADV> >>> media: IEEE 802.11 Wireless Ethernet autoselect mode 11na <hostap> >>> status: running >>> ssid WatchTower channel 100 (5500 MHz 11a ht/40+) bssid 00:01:36:17:96:0e >>> regdomain DEBUG indoor authmode WPA2/802.11i privacy MIXED deftxkey 3 >>> AES-CCM 2:128-bit AES-CCM 3:128-bit txpower 14 scanvalid 60 >>> ampdulimit 64k ampdudensity 4 shortgi smps burst dtimperiod 1 >>> >>> >>> [2] ifconfig mwl0_wlan1 list sta (w/addr removed) >>> AID CHAN RATE RSSI IDLE TXSEQ RXSEQ CAPS FLAG >>> 1 120 54M 33.0 0 1537 25952 EP A RSN (rssi 68:20:20 nf >>> 0:0:0) >> >> mwl supports HT rates, but it looks like your AP is not sending HT rates to >> you. > > Thanks for the quick clarification, that's very encouraging to find out! > > In this case, the mwl card is the AP. The client line is from an > associated Windows 7 laptop with an Intel 5100abgn card which does show > the AP as 802.11n in the AP list. I'm connected and sending this message > through it right now, actually. > > Are there some other bits that need set in order to have clients > associate with HT rates? Or some other prerequisite conditions such as > number of attached antennae? I do only have one antenna attached as I > didn't have a second pigtail for this test unit's case. The card > actually has three connectors.
Having only 1 antenna connected will likely impact your connection. > I didn't see hints in the mwl(4), wlan(4), hostapd(8), hostapd.conf(5), > or ifconfig(8) man pages about troubleshooting rates. I see plenty of > talk in ifconfig(8) about use and control of HT rates, but given what > I'm seeing in ifconfig, it should be set to use them. I've tried several > combinations of channels and standards (e.g. 11ng, 11na) but always end > up with a 54Mbps link. > > I'd appreciate any more pointers that you (or anyone else reading) may > have. I'd like to write up something on the topic once I get it fully > operational. I don't know what's happening, but I guess your Windows 7 laptop isn't sending the necessary HT rates in the association. Try using wlandebug to see what's happening. -- Rui Paulo _______________________________________________ freebsd-stable@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-stable To unsubscribe, send any mail to "freebsd-stable-unsubscr...@freebsd.org"