Muito estranho... Se está criado o volume e esta associado com o seu servidor teria que reconhecer. Verifica no storage se está tudo correto mesmo, pois eu ainda acho que não está associado a sua placa em algum volume criado.
Manda o teu config do kernel. Abraços Mauro Felipe wrote: > 2006/5/4, Marcus Alves Grando <[EMAIL PROTECTED] > <mailto:[EMAIL PROTECTED]>>: > > Mauro, > > Você adicionou o ispfw no kernel ou carregou via kernel module? > > Eu coloquei no kernel : > device isp > device ispfw > > > Via > software da placa (bios), ela reconhece o storage? > > > Não sei se ele está reconhecendo o storage, no dmesg não mostra nada a > não ser as HBA's. O storage é um MSA1000 e no software que uso para > falar qual unidade lógica vai ser apresentada para as HBA's, no caso > desse servidor está com o status offline, mas a conexão está certinha e > os leds estão verdes. > > Você liberou no > storage para o ID da sua placa conectar e em qual partição? > > > Eu liberei para ele conectar em um Logical Driver. Até o momento não > existe nenhuma partição criada, somente a unidade lógica que eu > disponibilizei para essas duas HBA's. > > > Coloca isso no teu /boot/devices.hint > hint.isp.0.topology="nport" > hint.isp.0.debug="7" > > Depois manda o dmesg novamente > > > DMESG depois do boot com a nova configuração do devices.hint: > > faraday# dmesg > Copyright (c) 1992-2005 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 6.0-RELEASE-p7 #0: Wed May 3 15:02:04 BRT 2006 > [EMAIL PROTECTED]:/usr/src/sys/i386/compile/FARADAY > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: Intel(R) Xeon(TM) CPU 3.06GHz (3047.93-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0xf29 Stepping = 9 > > Features=0xbfebf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > > Features2=0x4400<CNTX-ID,<b14>> > Hyperthreading: 2 logical CPUs > real memory = 2147459072 (2047 MB) > avail memory = 2096488448 (1999 MB) > npx0: [FAST] > npx0: <math processor> on motherboard > npx0: INT 16 interface > acpi0: <COMPAQ P29> on motherboard > acpi0: Power Button (fixed) > pci_link0: <ACPI PCI Link IUSB> on acpi0 > pci_link1: <ACPI PCI Link IN16> on acpi0 > pci_link2: <ACPI PCI Link IN17> on acpi0 > pci_link3: <ACPI PCI Link IN18> on acpi0 > pci_link4: <ACPI PCI Link IN19> on acpi0 > pci_link5: <ACPI PCI Link IN20> on acpi0 > pci_link6: <ACPI PCI Link IN21> on acpi0 > pci_link7: <ACPI PCI Link IN22> on acpi0 > pci_link8: <ACPI PCI Link IN23> on acpi0 > pci_link9: <ACPI PCI Link IN24> on acpi0 > pci_link10: <ACPI PCI Link IN25> on acpi0 > pci_link11: <ACPI PCI Link IN26> on acpi0 > pci_link12: <ACPI PCI Link IN27> on acpi0 > pci_link13: <ACPI PCI Link IN28> on acpi0 > pci_link14: <ACPI PCI Link IN29> on acpi0 > pci_link15: <ACPI PCI Link IN30> on acpi0 > pci_link16: <ACPI PCI Link IN31> on acpi0 > pci_link17: <ACPI PCI Link IN32> on acpi0 > pci_link18: <ACPI PCI Link IN33> on acpi0 > pci_link19: <ACPI PCI Link IN34> on acpi0 > Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000 > acpi_timer0: <32-bit timer at 3.579545MHz > port 0x920-0x923 on acpi0 > cpu0: <ACPI CPU> on acpi0 > pcib0: <ACPI Host-PCI bridge> on acpi0 > pci0: <ACPI PCI bus> on pcib0 > pci0: <display, VGA> at device 3.0 (no driver attached) > pci0: <base peripheral> at device 4.0 (no driver attached) > pci0: <base peripheral> at device 4.2 (no driver attached) > isab0: <PCI-ISA bridge> at device 15.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <ServerWorks CSB5 UDMA100 controller> port > 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x2000-0x200f at device 15.1 on pci0 > ata0: <ATA channel 0> on atapci0 > ata1: <ATA channel 1> on atapci0 > ohci0: <OHCI (generic) USB controller> mem 0xf5ef0000-0xf5ef0fff irq 7 > at device 15.2 on pci0 > ohci0: [GIANT-LOCKED] > usb0: OHCI version 1.0, legacy support > usb0: SMM does not respond, resetting > usb0: <OHCI (generic) USB controller> on ohci0 > usb0: USB revision 1.0 > uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 4 ports with 4 removable, self powered > pcib1: <ACPI Host-PCI bridge> on acpi0 > pci1: <ACPI PCI bus> on pcib1 > ciss0: <Compaq Smart Array 5i> port 0x3000-0x30ff mem > 0xf7bc0000-0xf7bfffff,0xf7af0000-0xf7af3fff irq 10 at device 3.0 on pci1 > ciss0: [GIANT-LOCKED] > pcib2: <ACPI Host-PCI bridge> on acpi0 > pci2: <ACPI PCI bus> on pcib2 > bge0: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem > 0xf7cf0000-0xf7cfffff irq 11 at device 1.0 on pci2 > miibus0: <MII bus> on bge0 > brgphy0: <BCM5703 10/100/1000baseTX PHY> on miibus0 > brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, > 1000baseTX-FDX, auto > bge0: Ethernet address: 00:0e:7f:21:61:37 > bge1: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem > 0xf7ce0000-0xf7ceffff irq 15 at device 2.0 on pci2 > miibus1: <MII bus> on bge1 > brgphy1: <BCM5703 10/100/1000baseTX PHY> on miibus1 > brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, > 1000baseTX-FDX, auto > bge1: Ethernet address: 00:0e:7f:21:61:36 > pcib3: <ACPI Host-PCI bridge> on acpi0 > pci3: <ACPI PCI bus> on pcib3 > isp0: <Qlogic ISP 2312 PCI FC-AL Adapter> port 0x4000-0x40ff mem > 0xf7df0000-0xf7df0fff irq 15 at device 1.0 on pci3 > isp0: [GIANT-LOCKED] > isp0: Board Type 2312, Chip Revision 0x2, loaded F/W Revision 3.3.6 > isp0: Installed in 64-Bit PCI slot > isp0: 839 max I/O commands supported > isp0: NVRAM Port WWN 0x210000e08b11c60d > pcib4: <ACPI Host-PCI bridge> on acpi0 > pci6: <ACPI PCI bus> on pcib4 > isp1: <Qlogic ISP 2312 PCI FC-AL Adapter> port 0x5000-0x50ff mem > 0xf7ff0000-0xf7ff0fff irq 11 at device 1.0 on pci6 > isp1: [GIANT-LOCKED] > bge2: <Broadcom BCM5701 Gigabit Ethernet, ASIC rev. 0x105> mem > 0xf7fe0000-0xf7feffff irq 7 at device 2.0 on pci6 > bge2: Ethernet address: 00:08:02:28:4a:b9 > pci6: <base peripheral, PCI hot-plug controller> at device 30.0 (no > driver attached) > acpi_tz0: <Thermal Zone> on acpi0 > atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > atkbd0: [GIANT-LOCKED] > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > psm0: [GIANT-LOCKED] > psm0: model IntelliMouse Explorer, device ID 4 > sio0: <Standard PC COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 > sio0: type 16550A > fdc0: <floppy drive controller (FDE)> port 0x3f2-0x3f5 irq 6 drq 2 on acpi0 > fdc0: [FAST] > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > pmtimer0 on isa0 > orm0: <ISA Option ROMs> at iomem > 0xc0000-0xc7fff,0xc8000-0xcbfff,0xee000-0xeffff on isa0 > ppc0: parallel port not found. > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio1: configured irq 3 not in bitmap of probed irqs 0 > sio1: port may not be enabled > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > Timecounter "TSC" frequency 3047929812 Hz quality 800 > Timecounters tick every 1.000 msec > isp0: Point-to-Point mode > isp0: Loop UP > isp0: Port Database Changed > isp0: Port Database Changed > isp0: Firmware State <Config Wait->Ready> > isp0: Target 126 (Loop 0x7e) Port ID 0xfffffe (role (none)) Arrived > Port WWN 0x200800606951ac31 > Node WWN 0x100000606951ac31 > isp0: 2Gb link speed/s > isp0: Loop ID 255, AL_PA 0x0, Port ID 0x10800, Loop State 0x2, Topology > 'F Port' > isp0: Target 255 (Loop 0xff) Port ID 0x10800 (role Initiator) Arrived > Port WWN 0x210000e08b11c60d > Node WWN 0x200000e08b11c60d > acd0: CDRW <DW-224E/A.1K> at ata0-master PIO4 > da0 at ciss0 bus 0 target 0 lun 0 > da0: <COMPAQ RAID 5 VOLUME OK> Fixed Direct Access SCSI-0 device > da0: 135.168MB/s transfers > da0: 69455MB (142245120 512 byte sectors: 255H 32S/T 17432C) > Trying to mount root from ufs:/dev/da0s1a > > > O camcontrol continua mostrando a mesma coisa. > > scbus0 on ciss0 bus 0: > <COMPAQ RAID 5 VOLUME OK> at scbus0 target 0 lun 0 (pass0,da0) > scbus1 on ciss0 bus 32: > scbus2 on ciss0 bus 33: > scbus3 on isp0 bus 0: > < > at scbus3 target -1 lun -1 () > scbus4 on isp1 bus 0: > < > at scbus4 target -1 lun -1 () > scbus-1 on xpt0 bus 0: > < > at scbus-1 target -1 lun -1 (xpt0) > > > > > -- > [ ]´s > > Mauro Felipe > > > ------------------------------------------------------------------------ > > _______________________________________________ > freebsd mailing list > freebsd@fug.com.br > https://www.fug.com.br/mailman/listinfo/freebsd -- Marcus Alves Grando marcus(at)corp.grupos.com.br | Grupos Internet S/A mnag(at)FreeBSD.org | FreeBSD.org _______________________________________________ freebsd mailing list freebsd@fug.com.br https://www.fug.com.br/mailman/listinfo/freebsd
