Вторник, 5 сентября 2023, 12:30 +07:00 от "Al Chu" <[email protected]>: > > A bunch of x9dr7 and sc-826TQ works only for FRU addresses. > > Does > > ipmi-oem supermicro get-power-supply-status 1|2|3 > work for the older ones?
ipmioem=ipmi-oem -h $IP -u $user -p $pass $ipmioem supermicro get-power-supply-status 1 good $ipmioem supermicro get-power-supply-status 2 good $ipmioem supermicro get-power-supply-status 3 supermicro:get-power-supply-status failed: NAK on Write Working. 2 power-supply. This is a relatively new motherboard. Works already at address 0x07 $ipmitool raw 0x06 0x52 0x07 0x70 0x01 0xa 0x07 -new 0x05 -old X7 series 0x70 - 1 power-supply 0x72 - 2 power-supply 0x74 - 3 power-supply 0xa - temperature 0xb - fan1 ----------- X7DBE-X get-power-supply-status 1|2|3, get-power-supply-status2 1|2|3, get-pmbus-power-supply-status 1|2|3 supermicro:get-pmbus-power-supply-status failed: Invalid data field in Request Does not work. > Al > > On 9/4/23 21:46, Андрей Грехов wrote: > > Hi. > > Понедельник, 4 сентября 2023, 22:27 +07:00 от "Al Chu" <[email protected]>: > >> Hi, > >> > >> I believe this is already implemented via > >> > >> ipmi-oem supermicro get-pmbus-power-supply-status 1|2|3 > >> > >> If you can confirm, I can document that it works on X9DRD too. > > I confirm. > > But it depends more on the type of case. > > Works for me on cs-825TQ. > > Which are connected by i1c connector "power 5 pin" and protocol PMBus > > (or old FRU) > > > > This should work from X8 to X11 "power 5 pin". > > I have X7DBE-X, but it works very unstable. > > > > A bunch of x9dr7 and sc-826TQ works only for FRU addresses. > > ipmitool -H $host -U $user -P $pass raw 0x06 0x52 0x05 0x$address 0x01 0x$d3 > > $address = 70|72|74 > > > > PWS-720-R > > $d3 : > > 0xA Temp, C > > 0xB Fan1, RPM=$izm*114,5 > > 0xС Fan2, RPM *114,5 > > ---------- > > There is no desire to add support for reading modern power supplies over the > PMBus (rev 1.0,1.1,1.2) ? > > > >> Al > >> > >> On 9/4/23 05:23, Андрей Грехов wrote: > >>> This working X9drd. PMBus rev.1.1-1.4 > >>> > >>> ipmitool -H $host -U $user -P $pass raw 0x06 0x52 0x07 0x78 0x01 0x88 > >> InputVoltage > >>> 0x78 first PowerSupply > >>> 0x7a second PowerSupply > >>> raw 0x06 0x52 0x07 0x78 0x01 0x90 Fan1 > >>> raw 0x06 0x52 0x07 0x78 0x01 0x91 Fan2 > >>> > >>> The's my old articl. > >>> > >>> Андрей Грехов > >> -- > >> Al Chu > >> Livermore Computing > >> Lawrence Livermore National Laboratory > >> > > > > Андрей Грехов > > -- > Al Chu > Livermore Computing > Lawrence Livermore National Laboratory > Андрей Грехов
