Thank you Sal. It seemed to fix our problem. I don't see any of these sync messages anymore.
You sure made my day.. well, in fact my whole week :) Do you know the difference between using broadcast or multicast? Is one prefered over the other ? Regards, Torkel > -----Original Message----- > From: Previtera, Sal [mailto:[EMAIL PROTECTED] > Sent: 16. september 2004 19:39 > To: [EMAIL PROTECTED] > Subject: Re: [FW-1] FLAPPING CROSSOVER > > > The problem is multicast and the type of Switch you are using > Try Broadcast instead, at the firewalls (both of them) issue > the following > commands; > > cphaconf set_ccp broadcast (change to broadcast mode) > > cphaprob -a if (see if all interface are using broadcast) > > If you do want to use broadcast, then you have to figure out why the > multicast version of Checkpoint and the Switch Vendor version are > incompatible. > > > > -----Original Message----- > From: Torkel Mathisen [mailto:[EMAIL PROTECTED] > Sent: Thursday, September 16, 2004 10:03 AM > To: [EMAIL PROTECTED] > Subject: Re: [FW-1] FLAPPING CROSSOVER > > Hi > > We also got some problems with flapping crossover or atleast > clusterxl. > > It may or not be the same problem as this. > > In our log we see this all the time: > > cluster_info: (ClusterXL) Interface Active Check on member 2 > (10.254.254.2) > detected a problem (5 interfaces required, only 4 up). > cluster_info: (ClusterXL) interface eth3 of member 2 > (10.254.254.2) is down > (receive down, transmit down) > cluster_info: (ClusterXL) Interface Active Check on member 2 > (10.254.254.2) > status OK. > cluster_info: (ClusterXL) member 2 (10.254.254.2) is up. > cluster_info: (ClusterXL) member 2 (10.254.254.2) is standby. > cluster_info: (ClusterXL) interface eth3 of member 2 > (10.254.254.2) is up > > A bit futher down (or just a little bit before, depending on > how you look at it) we get: > cluster_info: (ClusterXL) member 2 (10.254.254.2) is down. > > Note that the sync-interface is NOT eth3 so it actually reports > down on another interface. > > You see something like that in your logs Annette? > > And does anyone have an idea? > > Cluster running SPLAT R55 121 with Checkpoint HA only. > Interfaces is Intel e1000 which is autonegotiated to 1000 full. > > Regards, > Torkel > > > > -----Original Message----- > > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] > > Sent: 15. september 2004 15:31 > > To: [EMAIL PROTECTED] > > Subject: Re: [FW-1] FLAPPING CROSSOVER > > > > > > Are you running ClusterXL, or other? What OS? There are quite > > a few bugs I > > know of in just ClusterXL alone with synch... > > Perhaps I may be able to help you. Let the mailing list know. :-) > > > > > > Regards, > > Matt Goddard > > Security Information Team > > Schneider National > > 920-592-4787 > > [EMAIL PROTECTED] > > > > > > > > |---------+--------------------------------------------> > > | | "Garner, Annette K **BETH" | > > | | <[EMAIL PROTECTED]> | > > | | Sent by: Mailing list for | > > | | discussion of Firewall-1 | > > | | <[EMAIL PROTECTED]| > > | | KPOINT.COM> | > > | | | > > | | | > > | | 09/15/2004 06:18 AM | > > | | Please respond to Mailing list | > > | | for discussion of Firewall-1 | > > | | | > > |---------+--------------------------------------------> > > > > >------------------------------------------------------------- > > ---------------------------------| > > | > > | > > | To: > > [EMAIL PROTECTED] > > | > > | cc: > > | > > | Subject: [FW-1] FLAPPING CROSSOVER > > | > > > > >------------------------------------------------------------- > > ---------------------------------| > > > > > > > > > > I have swapped out the cable and switched to a new nic with > > the no luck. > > I turned off auto-negotiated and set it to 100baseTX-FD > > flow-control on > > both boxes. > > > > > > > > Thanks, > > > > Annette > > > > > > ================================================= > > To set vacation, Out-Of-Office, or away messages, > > send an email to [EMAIL PROTECTED] > > in the BODY of the email add: > > set fw-1-mailinglist nomail > > ================================================= > > To unsubscribe from this mailing list, > > please see the instructions at > > http://www.checkpoint.com/services/mailing.html > > ================================================= > > If you have any questions on how to change your > > subscription options, email > > [EMAIL PROTECTED] > > ================================================= > > > > ================================================= > > To set vacation, Out-Of-Office, or away messages, > > send an email to [EMAIL PROTECTED] > > in the BODY of the email add: > > set fw-1-mailinglist nomail > > ================================================= > > To unsubscribe from this mailing list, > > please see the instructions at > > http://www.checkpoint.com/services/mailing.html > > ================================================= > > If you have any questions on how to change your > > subscription options, email > > [EMAIL PROTECTED] > > ================================================= > > > > ================================================= > To set vacation, Out-Of-Office, or away messages, > send an email to [EMAIL PROTECTED] > in the BODY of the email add: > set fw-1-mailinglist nomail > ================================================= > To unsubscribe from this mailing list, > please see the instructions at > http://www.checkpoint.com/services/mailing.html > ================================================= > If you have any questions on how to change your > subscription options, email > [EMAIL PROTECTED] > ================================================= > > ================================================= > To set vacation, Out-Of-Office, or away messages, > send an email to [EMAIL PROTECTED] > in the BODY of the email add: > set fw-1-mailinglist nomail > ================================================= > To unsubscribe from this mailing list, > please see the instructions at > http://www.checkpoint.com/services/mailing.html > ================================================= > If you have any questions on how to change your > subscription options, email > [EMAIL PROTECTED] > ================================================= > ================================================= To set vacation, Out-Of-Office, or away messages, send an email to [EMAIL PROTECTED] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [EMAIL PROTECTED] =================================================
