On the stand-by machine do a 'cphaconf stat', what is the output? JT
On Tue, Jul 8, 2008 at 4:31 PM, Robers, Tom <[EMAIL PROTECTED]> wrote: > Hi Sergio, > > First, thanks for the reply. I do my job with Checkpoint products since > Firewall-1 v3.0. > Back to the problem: > After installation of HFA02 on my active machine (no reboot, yet) it is > quitting the HA-Cluster. Now I wasn't able to ping my manager, but > everything else works fine (Internet, etc). From the same network the ping > works. > After rebooting the machine I was able to reach the manager again. I did > the test to shutdown the active one and the same problem. > This is certainly not an issue of the hotfix. Maybe I have a config problem > with my standby. > > Regards > Tom > > -----Ursprüngliche Nachricht----- > Von: Mailing list for discussion of Firewall-1 [mailto: > [EMAIL PROTECTED] Im Auftrag von Sergio Alvarez > Gesendet: Montag, 7. Juli 2008 15:43 > An: [email protected] > Betreff: Re: [FW-1] NGXR65 HFA02 installation > > First of all Tom, you should have upgraded your Management server first, it > MUST be on the same or higher version of your firewall modules for > everything to work properly. > > Before trying to go forward with this, go ahead and read a pdf file named > CheckPoint_R65_UpgradeGuide, which you can find on any R65 installation > disc > or on the Check Point downloads site. > > Now, going back to your explanation, if you applied HFA02 to your > Management > server and you cannot ping to it, saying "the active one is blocking your > ping", makes no sense if you are not sending such ping through that active > firewall. Make sure you try from a machine on the same network. > > BTW, if your Management server got screwed up, pretty much the only way to > get it back would be reinstalling the machine and importing a backup... > hope > you had done you homework and generated a backup recently. > > Regards > > On Mon, Jul 7, 2008 at 6:35 AM, Robers, Tom <[EMAIL PROTECTED]> > wrote: > > > Hi all, > > > > we have one Management and two Gateways in HA-mode. > > I installed the HFA first on my standby machine, did a reboot and ok, so > > far. Next I installed it on my manager with the result that I even can't > > "ping" the machine. I don't have it installed on my active gateway. > > I think the active one is blocking my ping ! > > What can I do get my manager back ?? > > > > Regards > > Tom > > > > Scanned by Check Point Total Security Gateway. > > > > ================================================= > > To set vacation, Out-Of-Office, or away messages, > > send an email to [EMAIL PROTECTED] > > in the BODY of the email add: > > set fw-1-mailinglist nomail > > ================================================= > > To unsubscribe from this mailing list, > > please see the instructions at > > http://www.checkpoint.com/services/mailing.html > > ================================================= > > If you have any questions on how to change your > > subscription options, email > > [EMAIL PROTECTED] > > ================================================= > > > > > > -- > Sergio Alvarez > (506)8301342 > > > Scanned by Check Point Total Security Gateway. > > ================================================= > To set vacation, Out-Of-Office, or away messages, > send an email to [EMAIL PROTECTED] > in the BODY of the email add: > set fw-1-mailinglist nomail > ================================================= > To unsubscribe from this mailing list, > please see the instructions at > http://www.checkpoint.com/services/mailing.html > ================================================= > If you have any questions on how to change your > subscription options, email > [EMAIL PROTECTED] > ================================================= > > Scanned by Check Point Total Security Gateway. > > ================================================= > To set vacation, Out-Of-Office, or away messages, > send an email to [EMAIL PROTECTED] > in the BODY of the email add: > set fw-1-mailinglist nomail > ================================================= > To unsubscribe from this mailing list, > please see the instructions at > http://www.checkpoint.com/services/mailing.html > ================================================= > If you have any questions on how to change your > subscription options, email > [EMAIL PROTECTED] > ================================================= > -- ciao JT Scanned by Check Point Total Security Gateway. ================================================= To set vacation, Out-Of-Office, or away messages, send an email to [EMAIL PROTECTED] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [EMAIL PROTECTED] =================================================
