Hi, Which encryption algorithms do you use?
As far as I know iPhone doesn't support AES256. The same is probably true for iPAD. Regards, Torkel -----Original Message----- From: Mailing list for discussion of Firewall-1 [mailto:[email protected]] On Behalf Of Minh Quang Nguyen Sent: 22. juni 2010 15:59 To: [email protected] Subject: Re: [FW-1] Any success with IPAD L2TP Connection? Thanks for the input. I've followed everything step by step, the VPN connects successfully and I see encryption in the tracker but no dice. I've also noticed that once connected, the iphone can't reach the internet anymore. -Remote Access Rule allows full Internet browsing -L2TP connection works from a PC -Office mode set to all users -L2TP.conf file with password located on gateway under $FWDIR/conf -Remote Access -> Supports L2TP What else would you have configured? -----Original Message----- From: Mailing list for discussion of Firewall-1 [mailto:[email protected]] On Behalf Of Frank Darden Sent: Saturday, June 19, 2010 8:30 AM To: [email protected] Subject: Re: [FW-1] Any success with IPAD L2TP Connection? We have this working just fine with Iphones and Ipads as well. I can share our detailed configuration, however if you follow the referenced articles at http://www.checkpoint.com/iphone, and be sure to place the l2tp.conf file on the gateway, and also BE SURE route all traffic to gateway is set to yes, and that on your gateway you allow all traffic to be routed through the gateway, it should work. Frank On 6/14/10 10:11 AM, "M. N." <[email protected]> wrote: >Hi, >I was wondering if any of you were able to successfully establish a VPN >tunnel and access corporate resources using your IPAD to connect? > >We're running a NGX HFA60 firewall and the IPAD can successfully connect >to >the gateway but is unable to connect to any resources behind the central >office behind the firewall. Tracker is showing encrypted packets reaching >the gateway from the Office Mode IP. > > > >I've tried SK35409 about forcing the external IP address via Link >Selection >but it did not solve our problem. > > > >Normal L2TP connections from a PC are working without issues. > > > > > >Thanks > > > > > > > > > > >================================================= >To set vacation, Out-Of-Office, or away messages, >send an email to [email protected] >in the BODY of the email add: >set fw-1-mailinglist nomail >================================================= >To unsubscribe from this mailing list, >please see the instructions at >http://www.checkpoint.com/services/mailing.html >================================================= >If you have any questions on how to change your >subscription options, email >[email protected] >================================================= Scanned by Check Point Total Security Gateway. ================================================= To set vacation, Out-Of-Office, or away messages, send an email to [email protected] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [email protected] ================================================= Scanned by Check Point Total Security Gateway. ================================================= To set vacation, Out-Of-Office, or away messages, send an email to [email protected] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [email protected] ================================================= Scanned by Check Point Total Security Gateway. ================================================= To set vacation, Out-Of-Office, or away messages, send an email to [email protected] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [email protected] =================================================
