Hi Thanks for this, my problem is i boot into mgr mode, i enter boot -s ansd this asks for a password, i also tried install on bootmgr, this also asks for a password so i reset the device, but still the same, had another device and managed to get into boot -s and reset the password, not come across where boot -s and install asks for a password on a IP390 running ipso 4.1 Cheers
________________________________ From: Rennett Mbako Maphane <[email protected]> To: [email protected] Sent: Wednesday, 12 October 2011, 14:21 Subject: Re: [FW-1] [BULK] [FW-1] boot -s and install on bootmgr and config tool in 6.2 Peter Check if this can help you Password Recovery (IPSO 3.4 and above) You need to boot system into single user mode. To do this reboot the machine and when you see the line " boot: "you must enter "-s". (You have about 10 seconds) After it boots, it will ask you "Enter pathname of shell or RETURN for sh:", press Enter key. Enter "/etc/overpw" in the # prompt. It will ask if you want continue, type "y". In IPSO 3.4 and above, /etc/overpw will ask you to set a password. The admin password defaults to no password in earlier versions of IPSO. Reboot. Login as admin If a password is required, you will be asked for one. Use the dbpasswd command to set a new password: nokia[admin]# dbpasswd admin newpassword "" (Note that the "" is necessary to specify (NULL) as the old password.) Then, save this new password to the configuration file so that you can log into Network Voyager: nokia[admin]# dbset :save from the knowledge base regards Renny thank you and, ____________________ Kind Regards... Mr. Rennett M. Maphane DIT Security Division DDTel : 361 2600 TTDirectline : 361 2636 33Fax : 31 700 43 33Alternative Private Email [email protected] When MEN ARE MEN, WOMEN ARE FEW, AND SHEEP ARE NERVOUS -----Original Message----- From: Mailing list for discussion of Firewall-1 [mailto:[email protected]] On Behalf Of Peter Addy Sent: Tuesday, October 11, 2011 10:50 PM To: [email protected] Subject: [BULK] [FW-1] boot -s and install on bootmgr and config tool in 6.2 Importance: Low if boot -s and install at boot mgr both have a password set, and you dont know the password, how would one reset this, i have tried to reset the IP390 running on ipso 4.1, but no joy Also has anyone used the acquire migration tool in ipso 6.2? i have tried to import a ipso 4.2 into this 6.2, uploads fime, however then when i go to migrate config page, this remains blank, anyone had this expereince? Thanks Scanned by Check Point Total Security Gateway. ================================================= To set vacation, Out-Of-Office, or away messages, send an email to [email protected] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [email protected] ================================================= Scanned by Check Point Total Security Gateway. The contents of this communication, including attachments is strictly confidential and legally privileged, and is intended for the use of the named recipient(s). Any review, retransmission, dissemination, copying, disclosure or other use of, or taking an action in reliance upon this information by persons or entities other than the intended recipient is prohibited. If you have received this message in error, please notify the sender immediately by return email and delete the message. Any views expressed in this e-mail are those of the individual sender and no liability will attach to Government of Botswana. Please note that the recipient must scan this email and any attached files for viruses and the like. ================================================= To set vacation, Out-Of-Office, or away messages, send an email to [email protected] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [email protected] ================================================= ================================================= To set vacation, Out-Of-Office, or away messages, send an email to [email protected] in the BODY of the email add: set fw-1-mailinglist nomail ================================================= To unsubscribe from this mailing list, please see the instructions at http://www.checkpoint.com/services/mailing.html ================================================= If you have any questions on how to change your subscription options, email [email protected] ================================================= Scanned by Check Point Total Security Gateway.
