On Thu, Apr 16, 2009 at 11:12 AM, Yicheng Jia <[email protected]> wrote: > > Hi Nicolas, > > After this "reset" command, both ports are DOWN forever, I can only get > portinfo from local port. > > I am sure that the port that has been reset is not the local port, otherwise > it will prompt "node type not switch" error. > > I tried to enable this switch port from another port and brought it to > POLLING state, but as long as I use "reset", both ports are DOWN.
What are the peer port's LinkDownDefaultStates ? Sounds like one or more must be Sleeping rather than Polling for some reason. -- Hal > Thanks! > > Yicheng Jia > > > > > Nicolas Morey-Chaisemartin <[email protected]> > > 04/16/2009 12:43 AM > > To > Yicheng Jia <[email protected]> > cc > [email protected] > Subject > Re: [ofa-general] link width problem of Qlogic 9024 unmanaged switch > > > > > By any chances have you not reset the port you're on? > Have you tried using another node to enable the port again? > > Nicolas > > Le 16/04/2009 00:45, Yicheng Jia a écrit : >> >> Hello Randy, >> >> I am trying to run "ibportstate reset" to reset the switch port on the >> other side in order to get 4x link. However I get the following error: >> ibwarn: [19660] mad_rpc: _do_madrpc failed; dport (Lid 7) >> ibportstate: iberror: failed: smp set portinfo failed >> >> And the port status change to DOWN after this. Have you ever tried to >> run "ibportstate" to reset the switch port? >> >> Thanks! >> >> Yicheng Jia >> >> >> >> >> >> ------------------------------ >> >> Message: 2 >> Date: Wed, 4 Mar 2009 18:39:54 -0600 >> From: Randy Halverson <[email protected]> >> Subject: [ofa-general] link width problem of Qlogic 9024 unmanaged >> switch >> To: "'[email protected]'" <[email protected]> >> Message-ID: >> <[email protected]> >> Content-Type: text/plain; charset="us-ascii" >> >> Hello Yicheng, >> >> After checking internally, this appears to be a known problem with older >> firmware for the 9024FC switches. >> >> It appears that you or another person at 'tmriusa.com' has recently >> opened a case with QLogic Tech Support for this issue. Please continue >> to work with QLogic Tech Support on firmware upgrade resolution since >> you probably don't have our FastFabric Tools to manage the 9024FC >> switches.. >> >> Regards, >> >> Randy >> Technical Support >> QLogic Corporation >> -------------- next part -------------- >> >> >> >> _____________________________________________________________________________ >> Scanned by IBM Email Security Management Services powered by >> MessageLabs. For more information please visit http://www.ers.ibm.com >> >> _____________________________________________________________________________ >> <http://www.ers.ibm.com/> >> >> >> _____________________________________________________________________________ >> Scanned by IBM Email Security Management Services powered by >> MessageLabs. For more information please visit http://www.ers.ibm.com >> >> _____________________________________________________________________________ >> >> >> ------------------------------------------------------------------------ >> >> _______________________________________________ >> general mailing list >> [email protected] >> http://lists.openfabrics.org/cgi-bin/mailman/listinfo/general >> >> To unsubscribe, please visit >> http://openib.org/mailman/listinfo/openib-general > > > _____________________________________________________________________________ > Scanned by IBM Email Security Management Services powered by MessageLabs. > For more information please visit http://www.ers.ibm.com > _____________________________________________________________________________ > > > _____________________________________________________________________________ > Scanned by IBM Email Security Management Services powered by MessageLabs. > For more information please visit http://www.ers.ibm.com > _____________________________________________________________________________ > > _______________________________________________ > general mailing list > [email protected] > http://lists.openfabrics.org/cgi-bin/mailman/listinfo/general > > To unsubscribe, please visit > http://openib.org/mailman/listinfo/openib-general > _______________________________________________ general mailing list [email protected] http://lists.openfabrics.org/cgi-bin/mailman/listinfo/general To unsubscribe, please visit http://openib.org/mailman/listinfo/openib-general
