Hey Justin , you sound like Mark Zuckerberg :) Here is the command I used:
gmx trjconv -f traj -o confout5000.gro -b 10000 -e 10000 and it gives the write gro with DNA in the box as it should be. This confout.gro is not the same as came out from the GMX run, at the same moment as the TRJ and XTC came Sergio Manzetti [ http://www.fjordforsk.no/logo_hr2.jpg ] [ http://www.fjordforsk.no/ | Fjordforsk AS ] [ http://www.fjordforsk.no/ | ] Midtun 6894 Vangsnes Norge Org.nr. 911 659 654 Tlf: +47 57695621 [ http://www.oekolab.com/ | Økolab ] | [ http://www.nanofact.no/ | Nanofactory ] | [ http://www.aq-lab.no/ | AQ-Lab ] | [ http://www.phap.no/ | FAP ] From: "Justin Lemkul" <jalem...@vt.edu> To: "gmx-users" <gmx-us...@gromacs.org> Sent: Thursday, September 7, 2017 2:55:05 PM Subject: Re: [gmx-users] DPOSRES not working On 9/7/17 8:45 AM, Sergio Manzetti wrote: > It seems that GMX simply didn't write out the correct frame. The confout.gro > file written out is written at the same time as the trajectories, and for > some reason, this confout.gro file has nothing to do with the last output > frame from the sims, when produced by gmx trjconv.. confout.gro is the final frame, re-wrapped for PBC. So it may "look" different from the final frame of the trajectory, but it's not. Unless you actually provide answers to the questions I asked and any actual commands you're issuing (e.g. what did you do when you say "produced by gmx trjconv" for instance?), then there's nothing anyone here can do to help you. We can't see what you're seeing or interpret what's in your mind :) -Justin > > > > > > Sergio Manzetti > > [ http://www.fjordforsk.no/logo_hr2.jpg ] > > [ http://www.fjordforsk.no/ | Fjordforsk AS ] [ http://www.fjordforsk.no/ | ] > Midtun > 6894 Vangsnes > Norge > Org.nr. 911 659 654 > Tlf: +47 57695621 > [ http://www.oekolab.com/ | Økolab ] | [ http://www.nanofact.no/ | > Nanofactory ] | [ http://www.aq-lab.no/ | AQ-Lab ] | [ http://www.phap.no/ | > FAP ] > > > > From: "Justin Lemkul" <jalem...@vt.edu> > To: "gmx-users" <gmx-us...@gromacs.org> > Sent: Thursday, September 7, 2017 2:28:23 PM > Subject: Re: [gmx-users] DPOSRES not working > > On 9/7/17 5:28 AM, Sergio Manzetti wrote: >> Hi Johannes, yes, they are there in both cases: >> >> ; Include Position restraint file >> #ifdef POSRES >> #include "posre_DNA_chain_E.itp" >> #endif >> > Do you have a position restraint energy term written in your .log file, > and if so, what is its magnitude? Does your DNA start at the middle of > the box (GROMACS convention) or at the coordinate origin (like other > software)? If you watch the trajectory evolve, what happens? Does the > DNA move a lot or does it just bounce back and forth around its original > position (suggesting your box is simply too small and any time an atom > crosses a boundary, you get a jump)? > > -Justin > -- ================================================== Justin A. Lemkul, Ph.D. Assistant Professor Virginia Tech Department of Biochemistry 303 Engel Hall 340 West Campus Dr. Blacksburg, VA 24061 jalem...@vt.edu | (540) 231-3129 http://www.biochem.vt.edu/people/faculty/JustinLemkul.html ================================================== -- Gromacs Users mailing list * Please search the archive at http://www.gromacs.org/Support/Mailing_Lists/GMX-Users_List before posting! * Can't post? Read http://www.gromacs.org/Support/Mailing_Lists * For (un)subscribe requests visit https://maillist.sys.kth.se/mailman/listinfo/gromacs.org_gmx-users or send a mail to gmx-users-requ...@gromacs.org. -- Gromacs Users mailing list * Please search the archive at http://www.gromacs.org/Support/Mailing_Lists/GMX-Users_List before posting! * Can't post? Read http://www.gromacs.org/Support/Mailing_Lists * For (un)subscribe requests visit https://maillist.sys.kth.se/mailman/listinfo/gromacs.org_gmx-users or send a mail to gmx-users-requ...@gromacs.org.